|
Trade Verify
Address: No.155 Shangcun Qingxiyang Industry Zone,Fuan city,Fujian,China
Contact name:Semmy Wu
Fuan Zhongzhi Pump Co., Ltd. |
|
Verified Suppliers
|
|
|
Peripheral Water Pump Description
The new peripheral water pump is optimized based on the original pump, which is a new design, beautiful, economical, safe, reliable, and easy to use. 100% copper coil, silicon steel stator, stainless steel rotor shaft, not easy to rust, long service life. Ceramic mechanical seals, peripheral impellers made of brass, and several radial blades at the end of the impeller. They are uniquely designed to provide more energy for the pumped liquid. In addition, the special shaping of the blades creates a rapid radial recovery movement of fluid between the blades of the impeller and the pump body.
The vortex water pump casing is produced using a special machine tool to ensure that the bearings, shaft, and pump casing are concentric, providing better reliability and maintainability. The clean water pump is a high lift, small size, low power consumption, easy to use and maintain.
Peripheral Water Pump Application
(1) Applicable to urban environmental protection, construction, fire protection, chemical, pharmaceutical, dye, printing and dyeing, brewing, electric power, electroplating, paper making, Oil, mine, equipment cooling, oil tanker unloading, etc.
(2) Applicable to clean water, seawater, and chemical medium liquid with acidity and alkalinity and slurry with general paste (medium viscosity ≤100 centipoises, solid content up to 30% or less).
(3) Install the rocker-type sprinkler, and then spray the water into the air, then spray it into small raindrops, which are farms, nurseries, orchards. Good equipment for tea gardens.
(4) It can be used with any type and specification of filter press, and the slurry is sent to the filter machine for pressure filtration.
Peripheral Water Pump Data ( 220V/50HZ )
| Model | Power | Current | Capacitor | H.Max | Q.Max | Pipe Size | |
| (HP) | (W) | (A) | (UF) | (m) | (L/min) | (m) | |
| PKM60 | 0.5 | 370 | 1.8 | 10 | 38 | 35 | 1”x1” |
| PKM70 | 0.75 | 550 | 3.5 | 15 | 50 | 45 | 1”x1” |
| PKM80 | 1 | 750 | 4 | 20 | 60 | 50 | 1”x1” |
| QB-60L | 0.5 | 370 | 1.8 | 10 | 38 | 35 | 1”x1” |
| QB-70L | 0.75 | 550 | 3.5 | 15 | 50 | 45 | 1”x1” |
| QB-80L | 1 | 750 | 4 | 20 | 60 | 50 | 1”x1” |
| DB-125 | 0.5 | 370 | 1.8 | 10 | 38 | 35 | 1”x1” |
| KF/1 | 0.5 | 370 | 1.8 | 10 | 38 | 35 | 1”x1” |
| PM16 | 0.5 | 370 | 1.8 | 10 | 35 | 35 | 1"X1" |
Peripheral Water Pump Construction
Pump
Pump Body: Cast iron/Brass/Stainless steel
Impeller: Brass impeller
Mechanical Seal: Carbon
Frant Cover: Cast iron/Cast iron with a brass insert/Stainless
steel
Motor
Single Phase
Heavy-Duty Continuous Work
Motor Housing: Aluminum
Shaft: Carbon Steel / Stainless Steel
Insulation: Class B / Class F
Protection: IP44 / IP54
Cooling: External Ventilation
Construction and safety standards in compliance with IEC
220V/50HZ.60HZ 110V/50HZ.60HZ 220v.110v/50hz.60hz are available on request.
Peripheral Water Pump Use Precautions:
Before preparing to install the pump, first check whether the firmware of each part is loose or not. There is no foreign matter jam in the pump flow path to avoid the situation that it cannot be cleaned after the later installation. Next, check the water source and water level before use. For the pump to work properly, you should install it in a covered area or a closed environment. Avoid using pumped water or non-corrosive liquids, and no sand or other solid impurities.
STRUCTURAL CHARACTERISTICS
| Main Specification | Standard | Optional |
| Transmission medium | Vortex Water | |
| Pump body | Cast Iron | |
| Impeller | Brass | |
| Motor housing | Aluminum | |
| Stator&Rotor | 1.Cold-rolled silicon steel sheet by high-speed punching machine. 2. 100% high-quality copper wire | |
| Front cover | Cast Iron | Brass plate embedded to avoid impeller jam |
| Bearing | Chinese Best Quality Bearing | NSK, SKF, or on request |
| Mechanical seal | Graphene/Ceramic | Silicon Carbon |
| Shaft | Carbon Steel | Stainless Steel |
| Insulation | Class B | Class F |
| Protection | IP44 | IP54 |
| Voltage | 220-240V Single Phase | On Request |
| Frequency | 50HZ | 60HZ |
| thermal protection | No | Yes |
| Automatic Pressure Control System | No | Yes |
| Cooling Type | External Ventilation | |
| Max. Suction lift | 9M | |
| Max. Fluid Temperature | +60℃ | |
| Max. Environment Temperature | +40℃ | |
| Installation | Horizontal | |
| Connect Type | Thread | |
| CONSTRUCTION AND SAFETY STANDARDS in compliance with IEC | ||
 |  |  |
 |  |  |
 |  |  |
Peripheral Water Pump GUARANTEE
Guarantee for one year from shipped on board date. During the
guarantee period, our company will provide free easy-damaged spare
parts for problems caused by our quality of production or raw
material, except the damageable spare parts caused by the
customer's incorrect artificial operation. In addition, after
expiration, our company provides cost spare parts for maintenance.
FAQ
1. Q: What’s the MOQ?
A: Trial sample order is ok.
2. Q: Are you a factory or trading company?
A: We are a manufacturer.
3. Q: Can you accept using our logo?
A: Yes, we can do OEM for you.
4. Q: How can I get the pump?
A: Usually, we suggest express for samples. If the volume reaches
1m³, the Seaway will be better.
5. Q: What’s the warranty period?
A: 1 year.
