Results fordouble caps physiotherapy infrared lampfrom 17022 Products.
|
Not go gauges for caps on finished lamps B22, 7006-10-8 According to standard IEC 60061-3 Purpose: To check dimension A in, of caps B22 on finished lamps. Testing: Caps on finished ...
|
|
|
|
High Standard Rj45 Network Connector Double Layer With LED Lamp Custom Products Application RJ45 is a type of information socket connector in a wiring system, consisting of a plug ...
china
|
|
|
square double venture LED ceiling lamps with Dali dimmable ballasts Light Source: LED Item Type: Downlights LED Light Source: Epistar chip Warranty(Years): 2 Input Voltage(V): 100-240 Lamp Power(W): 6 Lamp Luminous Flux...
|
|
|
|
Not go gauges for caps on finished lamps B15, 7006-10-8 According to standard IEC 60061-3 Purpose: To check dimension A in, of caps B15 on finished lamps. Testing: Caps on finished ...
|
|
|
|
BS EN 60061-3,NF EN 60061-3,DIN EN 60061-3,IEC EN 60061-3,CEI 60061-3 7006-28B-1 Not Go Gauge for E14 Caps on Finished Lamps Not go gauge for E14 caps on finished lamps, 7006-28B-1 ...
|
|
|
|
IEC60061-3: 7006-46A-3 Go Gauge for Bi-pin Cap on Finished Lamps G5 IEC60061-3 G5 Lamp Cap Go Gauge (7006-46A-3) Purpose: To check dimensions E max., F min., F max., and the ...
|
|
|
|
Go gauge for caps on finished lamps E12, 7006-27H-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E12 caps on finished lamps. Testing: ...
|
|
|
|
Go gauge for caps on finished lamps E17, 7006-27K-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E17 caps on finished lamps. Testing: ...
|
|
|
|
Go gauge for caps on finished lamps E12, 7006-27H-1 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E12 caps on finished lamps. Testing: ...
|
|
|
|
NF EN 60061-3, DIN EN 60061-3, IEC EN 60061-3, BS EN 60061-3 7006-27G-1 Go Gauge for Dimension "S1" of E14 Caps on Finished Lamp Go gauge for dimension "S1" of E14 caps on finished ...
|
|
|
|
The sharp part of the edge of the thread shall be broken with a radius of 0.2 mm to 0.3 mm. PURPOSE: To check the maximun dimensions of the crew thread and dimension T1 min, of E39 ...
|
|
|
|
Go gauge for caps on finished lamps E40, 7006-27-7 Purpose: To check the maximum dimensions of the screw thread and dimension T1 minimum of E40 caps on finished lamps. Testing: ...
|
|
|
|
IEC60061-3: 7006-27-7 E40 Go Gauge for Caps on Finished Lamps Go gauge for caps on finished lamps E40, 7006-27-7 Purpose: To check the maximum dimensions of the screw thread and ...
|
|
|
|
Go gauges for caps on finished lamps BA9, B15, BA15 & B22, 7006-11-8. According to standard IEC 60061-3 Purpose: To check dimensions A max., N min. D1 min., D1 max., and the ...
|
|
|
|
IEC60061-3: 7006-24C-1 E39 No Go Gauge for Caps on Finished Lamps The drawing is intended only to illustrate the essential dimensions of the gauge. For details of cap E39, see ...
|
|
|
|
IEC60061-3: 7006-51-2 Gauge for Caps on Finished Lamps for Testing Protect Against Accidental Contact E27/51*39. Gauge for E27/51x39 caps on finished lamps for testing protect ...
|
|
|
|
Not go gauge for caps on finished lamps E40, 7006-28D-1 Purpose: To check the minimum outside (major) diameter of the screw thread, dimension d, of E40 caps on finished lamps. ...
|
|
|
|
Not go gauge for caps on finished lamps E12, 7006-28C-1 Purpose: To check the minimum outside (major) diameter of the screw thread, dimension d, of E12 caps on finished lamps. ...
|
|
|
|
CEI60061-3, EN60061-3, DIN60061-3, IEC60061-3, BS60061-3 7006-28A-1 Not Go Gauge for E27 Caps on Finished Lamps Purpose: To check the minimum outside (major) diameter of the screw ...
|
|
|
|
Not go gauge for caps on finished lamps E12, 7006-28C-1 Purpose: To check the minimum outside (major) diameter of the screw thread, dimension d, of E12 caps on finished lamps. ...
|
|
|