Active Member
|
[China]
Address: Room No.401, 4th Floor, Building No. 46, ZTE Industrial park, No. 1776 East Hanghai Road, Economic-Technological Development Zhengzhou City, China, 450016
Contact name:Julia Zhu
Henan Dingli Medical Technology Co., Ltd |
|
|
Lumis 150 ST is a non invasive ventilator designed for non
dependent patients with respiratory insufficiency. Featuring
ResMed's unique volume assurance mode - iVAPS (intelligent Volume
Assured Pressure Support) - Lumis 150 VPAP ST maintains target
alveolar ventilation to suit each patient's changing needs.
Optional AutoEPAP ensures adequate EPAP is delivered to maintain an
open upper airway - automatically, while an intelligent Backup Rate
(iBR) encourages spontaneous breathing. Lumis 150 ST is also easy
to set up and use.
Key Features
iVAPS
intelligent Backup Rate (iBR)
AutoEPAP maintains upper airway patency
Vsync
TiControl
5 Trigger and Cycle Senstivities
QuickNav for low touch therapy adjustments
Climate Control Auto for automatic humidification
Ramp and Rampdown for extra comfort.
supported by ResScan 5.4
Specifications
Height | 150 mm |
|---|---|
Weight | 1268 gm |
Breadth | 255 mm |
Length | 116 mm |
Sound pressure level | 27 dBA with uncertainty of 2 dBA |
Standard air filter | Material: Polyester non woven fibre Average arrestance: >75% for ~7 micron dust |
Aircraft use | ResMed confirms that device meets the Federal Aviation Administration (FAA) requirements (RTCA/DO-160, section 21, category M) for all phases of air travel. |
Modes | CPAP, S, T, ST with optional iBR, PAC, iVAPS with iBR and optional Auto EPAP |
Water capacity | To maximum fill line 380 mL |
Sensors | Pressure sensor: Internally located at device outlet, analogue gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa) Flow sensor: Internally located at device inlet, digital mass flow type, -70 to +180 L/min |
Maximum single fault steady pressure | Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec. |
Housing construction | Flame retardant engineering thermoplastic |
Cleanable humidifier | material: Injection moulded plastic, stainless steel and silicone seal |
Operating pressure range | S, ST, T, PAC, iVAPS: 2 to 25 cm H2O (2 to 25 hPa) CPAP 4 to 20 cm H2O (4 to 20 hPa) |
Operating temperature/ humidity/altitude | +5°C to +35°C / 10 to 95% relative humidity, non-condensing / Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to 738 hPa |
Storage and transport temperature/humidity | -20°C to +60°C / 5 to 95% relative humidity, non-condensing |
Supplemental oxygen | Maximum flow: 15 L/min (S, ST, T, PAC, CPAP), 4 L/min (iVAPS) |
Air outlet | (complies with ISO 5356-1:2004): 22 mm |
Electromagnetic compatibility | requirements (EMC) according to IEC 60601-1-2:2014, for residential, commercial and light industry environments. It is recommended that mobile communication devices are kept at least 1 m away from the device. |
IEC 60601-1:2005+A1:2012 classification | Class II (double insulation), Type BF, Ingress protection IP22 |
