Active Member
|
[China]
Address: Guandaohe Village, Yuquan Office, Dangyang City, Hubei Province, China
Contact name:Jason Shao
Sinoma (Yichang) Energy Conservation New Material Co., Ltd. |
|
|
Fiber Cement Board is a composite material made of quartz sand,
cement and cellulose fibers. This product adopts imported pure
paper pule from Canada, not included waste paper pulp. Fiber cement
board is manufactured in a sheet form and they are used for
interior and exterior suspension, partition and flooring
application.The normal size is 1220×2440mm,thickness from 4.5~20mm,
and density is 1.3~1.6g/cm3. There are low-density, middle-density
and high-density.
Main Characteristic
1. 100% Asbestos Free
2. Excellent Fire Resistant
3. Excellent Moisture / Water Resistant
4. Good Heat and Sound Insulation
5. High Strength
6. Stable Dimensions
7. Durability and long service life
| |||
| Normal Size | 1220mm × 2440mm or 1200mm × 2400mm | ||
| Max. Width | 1220mm | ||
| Max. Length | 3000mm | ||
| Thickness | 4.5mm ~ 25mm | ||
| Color | Light Grey / Dark Grey / White / Black / Yellow / Green / Red | ||
| Edge | Square, Beveled | ||
| Density | 1.2 ~ 1.5kg/cm3 | ||
| Water Content | ≤10 | ||
| Water Absorption | ≤30 | ||
| Fire Resistance | Incombustibility A Class(GB8624-A) | ||
| Thermal Conductivity | Average≤0.20W/m.k | ||
| Bending Strength | Transverse≥11.0N/mm3, Vertical≥8.5N/mm3 | ||
| Radioactivity | Conforming to GB6566-2001 A Class | ||
| Asbestos | 100% Asbestos Free | ||
| Freeze Resistance | No distortion after 25 repeated cycles of freezing and thawing | ||
| Certification | SGS | ||
Partition Installing Method
1. Galvanized Metal Frame
a.The top and bottom keels are fixed respectively top floor and on
floor with expansion bolts.
b.The vertical keel should be aligned well according to the
requirement (generally being 612 mm) with
laterally supporting keel installed.
2. Board Material Package Fixed
a. Cutting the board material to the dimensions needed (about 10mm
lower than wall height)
b.Board material is fixed on keel in anchoring seam way with
tapping screw: the interval of tapping screw is generally
about 200~250mm with screws sinking 0.5mm under the board face.
c. The expansion seam of about 4mm between boards should be kept.
d. The shrouding should be fixed from the middle to the four sides
and cannot be operated at multipoint simultaneously
to avoid generating inner stress to make board material bucking.
e. Before board being packaged and fixed, depending the needs, glass cotton or rock cotton can be filled.
Ceiling Installing Method:
1. Carry out ceiling line-measuring to determine the ceiling’s
fixed position, the boom’s central range is generally 1200.
2. Connect and fix the boom and main keel with hanging piece to
make the main keel keep level position.
3. Vertically fix the sub-keel to the main keel with hanging piece;
the sub-keel axis’central range is 612mm.
4. Install the laterally supporting keel properly, its central
ranges is 1224mm.
5. Fix the board on sub-keels with tapping screws, and to well the
seam-connecting treatment.
Notice:
The hanging system of TITAN board combined with light steel keel is
divided into two kinds of person-standing type
and non person-standing type; for the non person-standing type,only
consider the self-weight of ceiling and light.Lamp
without loading other loads; for the person-standing type. Consider
about 80~100kg load when someone repaired it.
Transportation, Handing and Storage:
Deliver SINOMA Board to the project site in the original, unopened
package and store them in fully enclosed space where they will be
protected against damage from humidity, direct sunlight, surface
contamination and other causes of damage. Handle SINOMA Board
carefully to avoid chipping the edges or damaging units in any way.
Handling and storage practices should follow the manufacturer’s
recommended suggestions at all times.
