Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
Automatic feeder cutting production line, Dongguan Ruihui robot manufacturer
Automatic feeder cutting production line use process: the rolling hoist is put into the retracting reel of Ruihui hydraulic heavy-duty material frame by driving or forklift, start the heavy-duty material frame expansion and contraction cylinder, tighten the material roll, and then jog The material frame motor rotates the material head to the upper right side while the pneumatic pressure arm is pressed down on the surface of the roll, and then the tape is loosened.
Then slowly jog the unwinding and slowly pull the material out of the material to enter the middle (thick) plate leveling machine. At this time, the heavy material rack completes the loading and feeding operations.
After the material head is introduced into the leveling machine, the upper drum of the leveling machine is pressed down, the material frame is powered off, and then the material is moved by the Jinzhide middle (thick) plate leveling machine, and the material is adjusted several times according to the thickness of the material. The degree of depression of the flat drum has reached the optimum leveling effect, and then the material that has been leveled by the leveler is introduced into the NC feeder.
After the sheet falls to the table, the material is longitudinally fed, and then the horizontal direction is used to place the steel sheets neatly. The material level detection is provided at the front end of the material table.
When the stack height reaches the set value, the material table automatically drops. When the number of sheets of the seesaw reaches the set value, the automatic feeding stops, and the operator is required to hang the plate on the pallet, the picking counter is cleared, and the automatic circulation is entered to realize fully automated cutting production.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
