Active Member
|
[China]
Address: Floor 8, Bldg. 4, Jinyinxiandai City, Guangdian South Road, Jingsan Road, Jinshui Dist., Zhengzhou, Henan, China
Contact name:Eric Hao
HENAN DASION MACHINERY CO.,LTD |
|
|
Rebar bender machine mainly used for bending the common round steel,carbon steel, Ⅲ straight thread, and other construction projects, processing enterprises need various bending shape of the workpiece.This machine is mainly composed of drive gear, rack and workbench of three parts, transmission parts by motor through a triangle belt, pulley, gear shaft drive disc rotation, to complete the workpiece bending.
| Item | Rebar Bending Machine | Parameters |
| 1 | GW40(GW40B) | Bending range: Round steel bar ≤Φ30mm; Class-III rebar ≤Φ28mm Motor
Power: 3kw Wight: 210kg Dimension: 82*70*73cm Intermediate accessories Plate: 8mm |
| 2 | GW40A | Bending range: Round steel bar ≤Φ40mm;Class-III rebar ≤Φ32mm Motor
Power: 3kw Wight: 220kg Dimension: 82*70*73cm High-grade accessories Heavy Plate: 10mm. |
| 3 | GW45(GW45B) | Bending range: Round steel bar ≤Φ45 mm Class-III rebar ≤Φ36mm Motor Power: 3kw Weight: 255kg Dimension: 86*75*81cm High-grade accessories. Plate 10mm. Spindle with bearings. Thickening volute gear. |
| 4 | GW45A | Bending range: Round steel bar ≤Φ45 mm; Class-III rebar ≤Φ36mm
Motor Power: 4kw Weight: 310kg Dimension: 86*75*83cm High-grade accessories. Plate 10mm. Spindle with bearings,Heavy Double side operation |
| 5 | GW45AT | Bending range: Round steel bar ≤Φ45 mm Class-III rebar ≤Φ36mm Motor Power: 4kw Weight: 320kg Dimension: 88*75*84cm High-grade accessories. Plate 10mm. Spindle with bearings. Automatic operation |
| 6 | GW50(GW50B) | Bending range: Round steel bar ≤Φ50mm; Class-III rebar≤Φ40mm Motor
Power: 4kw Weight: 320kg Dimension: 85*83*83cm High-grade accessories. Plate 10mm. Spindle with bearings |
| 7 | GW50A | Bending range: Round steel bar ≤Φ50mm; Class-III rebar≤Φ40mm Motor
Power: 4kw Weight: 350kg Dimension:102*75*83cm High-grade accessories. Plate 10mm. Spindle with bearings. Digital Auto-control |
| 8 | GW55 (GW55B) | Bending range: Round steel bar≤Φ55mm; Class-III rebar≤Φ42mm Motor
Power: 5.5kw Weight: 420kg Dimension: 85*90*90cm High-grade accessories. Plate 10mm. |
1.Safty Operation
Check the electric parts as per the chart,plug into the pedal,connect with power to run unload at least 10 minutes.Must install the electric leakage switch and lack phase device,then confirm the rotate direction of the disk same to the mark on the sign.
Take bend accessories from the tool box in the cabinet,the put on the work disk as per the rebar dimension.
2.Manual Operation
Switch on the manual position,motor start button,adjust the disk to the start point,then put the rebar into the bend accessories.(rebar and block rod gap in 2-10mm )
Hold the start button until bend the rebar shape what you want.Hold another button,the disk back start then loose the button,finally finish work one time.
3. Semi-auto Operation
Adjust the switch on the semi position,make the two block to the start point and angle position what you want,put the rebar into the accessories.(rebar and block rod gap in 2-10mm ).
Start on motor or set pedal switch,motor drive disk to rotate bending the rebar,it would back automatically after finish bending work.Notice:Semi-auto just set the start button or pedal switch,automatic back to start. This type machine has the emergency stop button in symmetrical design,If occur the unappropriate operate or fault on equipment,the operator must press the button when leave from machine or off-duty.
