Results forclause 9 1 7 unjointed test probefrom 4972 Products.
|
IEC60598-1 1.1m Test Chain Made by 63% Cu and 37% Zn with CNAS Calibration Certificate 1. Introduction of Test Chain: Test chain is designed according to GB7000.1 and IEC60598-1 ...
|
|
|
|
IEC 60601-1-Figure 6 Standard test finger IEC61032 Figure 2, Diameter: 12mm Length:80mm Insulated portion: Ø50mm, 20mm wide,100mm long TESTING AND MEASURING EQUIPMENT/ALLOWED ...
|
|
|
|
Test Finger Probe , IEC 60335 Testing Probe Kit With Carrying Case Product information: 1.IEC Jointed Finger Probe 2.50mm Impact Test Ball 3.Test Pin Probe: short 4.Rigid Finger ...
|
|
|
|
IEC 61032 Figure 16 Test Thorn Probe 14 For Verifying Protection IEC61032 Figure 16 Test Probe 41 Test Thorn Probe For Verifying Protection Against Access To Glowing Heating ...
china
|
|
|
|
IEC 62368-1 Clause 8.6.2 Thrust Rod with Nylon Handle 100N / 250N Product information: The Thrust Rod conforms to the standard requirements of IEC 62368-1:2018 clause 8.6.2, T.2-T...
|
|
|
|
IEC61032 Figure 16 Test Finger Probe Test Thorn Probe With 80 Handle Length Standard: IEC61032 Protection of persons and equipment by enclosures - Probes for verification figure 16 ...
|
|
|
|
IEC 62196 Electric Vehicle IPX9K Water Ingress Testing Chamber Complied Standards & Clauses IEC 62196-1Ed.4CDV 2020 clause 20.2 IEC 60529:1989 + A1:1999 + A2:2013 Clause 14.2.9 ...
|
|
|
|
75g Fragmentation Test Hammer with Tungsten Carbide Tip for Glass According to IS015717 1. Introduction The test hammer for fragmentation test having a head with a mass of 75g±5g ...
|
|
|
|
IEC 60601-1-figure 7 Test Hook TESTING AND MEASURING EQUIPMENT/ALLOWED SUBCONTRACTING IEC 60601-1:2005 + Am.1:2012 Medical electrical equipment - Part 1: General requirements for ...
|
|
|
|
Test Rod Probe D Test Finger Probe IEC61032 Figure 4 Safety Testing Apparatus Product information: This probe conforms to the standard requirement of IEC61032 figure 4 test probe D ...
|
|
|
|
IEC 60335 Test Finger Probe Product information: 1. IEC Jointed Finger Probe 2. 50mm Impact Test Ball 3. test Pin Probe: short 4. Rigid Finger Probe 5. Ball Pressure Tester 6. ...
china
|
|
|
|
IEC 62368-1 Clause 5.4.11 Non - Inductive Resister 5k Ω For Current Leakage Product Information: This non-inductive resistor, category: wire-wound resistors. It is required by IEC ...
|
|
|
|
IEC61032 Figure 16 Test Finger Probe Test Thorn Probe With 80 Handle Length Standard: IEC61032 Protection of persons and equipment by enclosures - Probes for verification figure 16 ...
|
|
|
|
ISO17025 Approved Test Probe Kits IP Test Finger Probe Packed in Silver Box 1. Introduction: The test probe kits are used to verify the degrees of protection stiulated in IEC60529, ...
|
|
|
|
IEC 60335-2-11 clause 20.101 Integrated Door Endurance Tester For Durability And Structural Testing Of Household Appliance Product Introduction The integrated door endurance tester ...
|
|
|
|
IEC 61851-1 PLC Control System Leakage Tracking Test Equipment Product information: The tester is designed and manufactured according to the standard requirements of IEC60112, and ...
|
|
|
|
IEC61032 Test Finger Probe Test Probe C Test Rod for IP3X Testing 1. Introduction of Test Probe C: Designed according to IC61032 figure 3, meet the requirements of IEC60529-IP3, ...
|
|
|
|
IEC 60335-2-9 Figure 102 Stainless Steel 4.5 kg Load for Testing Rotating Spits Product overview: The testing rotating spits load complies with IEC 60335-2-9 clause 3.1.9.102 ...
|
|
|
|
IEC 62368-1 Clause 5.4.1.10 Thermal Resistance 20N Ball Pressure Test Switch Life Tester Product information: The ball pressure tester conforms to many standard requirements like ...
|
|
|
|
IEC 62368-1 Clause 5.4.2 Measuring Gauge Creepage Distance Test Cards Product information: These test gauges conform to IEC 62368-1 clause 5.4.1.10, IEC 60884-1 clause 25.2, 25.3, ...
|
|
|
You may also be interested in :