Home Companies RULETEAM CONNECTION TECHNOLOGY (SHENZHEN) CO.,LTD

DF13 wire to board connector terminals tin-plated Crimping Connector for Discrete wire AWG 30 to 26

Contact Us

[China]

Trade Verify

Address: No.A1507H2 Xinhe Century Building, 3069 Caitian Rd, Gangxia Community, Futian District, Shenzhen City, China

Contact name:Ricky Zou

RULETEAM CONNECTION TECHNOLOGY (SHENZHEN) CO.,LTD

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

DF13 wire to board connector terminals tin-plated Crimping Connector for Discrete wire AWG 30 to 26

Country/Region	china
City & Province	shenzhen guangdong
Categories	Terminals

Product Details

Specifiaction:
Category: Crimp Terminals
Series:A1252-TPE-A or A1252-GPE-A
Application:Signal
Material :Phosphor Bronze
Finish:Tin-plated or Gold-flash
Packaging Type: Reel
Termination Interface Style: Crimp or Compression
Wire Insulation Diameter:1.00mm(max)

Electrical & Mechanical information:
Current Rating: 1A AC, DC
Voltage Rating: 150V AC, DC
Contact Resistance: 30mΩ Max
Insulation Resistance:500MΩ Min
Withstanding Voltage: 500V AC/minute

Temperature range: -25℃ to 85 ℃

Ordering Information:

Part No.	Wire Range	Insulation O.D.	Material	Finish	Qty/reel
A1252-TPE-A	AWG26#-30#	1.00mm(Max)	Phosphor Bronze	Tin-plated	15Kpcs/reel
A1252-GPE-A				Gold-flash
Note:	E-stamping before tin-plated or Gold-flash

Drawing & testing report:

Please kindly check the following information to order right products.

1. Scope

This specification covers the requirements for product performance of 1.25mm pitch wire to board

connectors series.

2. Construction,Dimensions,Material & Plating

See the attached drawings

3. Ratings & Applicable Wires

Item	Standard
Rated Voltage (Max.)	150V AC/DC		Insulation O.D. 1.00mm (Max.)
Rated Current (Max.) And Applicable Wires	AWG#26	1A AC/DC
	AWG#28	1A AC/DC
	AWG#30	1A AC/DC
Ambient Temperature Range	-25℃ ~ +85℃*

*: Including terminal temperature rise

4. Electrical Performance

Test Description		Procedure	Requirement
4-1	Contact Resistance	Mate connectors, measure by dry circuit, 20mV max., 10mA.(Based upon JIS C5402 5.4)	30mΩ (Max.)
4-2	Insulation Resistance	Mate connectors, apply 500V DC between adjacent terminal or ground. (Based upon JIS C5402 5.2/MIL-STD-202 Method 302 Cond. B)	500MΩ (Min.)
4-3	Dielectric Withstanding Voltage	Mate connectors, apply 500V AC (rms) for 1 minute between adjacent terminal or ground. (Based upon JIS C5402 5.1/MIL-STD-202 Method 301)	No Breakdown.
4-4	Contact Resistance on Crimped Portion	Crimp the applicable wire on to the terminal, measure by dry circuit, 20mV (Max.)., 10mA.	5mΩ (Max.)

5. Mechanical Performance

Test Description		Procedure	Requirement
5-1	Actuator Insertion & Withdrawal Force	Insert and withdraw connectors at the speed rate of 25±3mm / minute.	Refer to paragraph 7
5-2	Crimping Pull Out Force	Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8)	AWG#26	2.0kgf (Min)
			AWG#28	1.0kgf (Min)
			AWG#30	0.8kgf (Min)
5-3	Terminal Insertion Force.	Insert the crimped terminal into the housing.	0.50kgf (Max.)
5-4	Terminal/Housing Retention Force.	Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing.	0.50kgf (Min.)
5-5	Pin Retention Force	Apply axial push force at the speed rate of 25±3mm / minute	0.50kgf (Min.)
5-6	Durability	When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute.	Contact Resistance 60mΩ (Max.)
5-7	Vibration	Amplitude: 1.5mm P-P Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes. (Based upon MIL-STD-202 Method 201A)	Appearance No Damage. Contact Resistance 60mΩ (Max.) Discontinuity 1 μsec.(Max.)
5-8	Physical Shock	490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A)

6. Environmental Performance And Others

Test Description		Procedure	Requirement
6-1	Temperature Rise	Carrying rated current load.(Based upon UL 498)	30℃(Max.)
6-2	Heat Resistance	85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A)	Appearance No Damage. Contact Resistance 60mΩ (Max.)
6-3	Cold Resistance	-25±3℃,96 hours (Based upon JIS C0020)	Appearance No Damage. Contact Resistance 60mΩ (Max.)
6-4	Humidity	Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B)	Appearance No Damage. Contact Resistance 60mΩ (Max.) Insulation Resistance 50MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3
6-5	Temperature Cycling	5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025)	Appearance No Damage. Contact Resistance 60mΩ (Max.)
6-6	Salt Spray	Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B)
6-7	SO2 Gas	24 hours exposure to 50±5ppm. SO2 gas at 40±2℃.
6-8	NH3 Gas	40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution.

6-9

Solderability

Soldering Time: 5±0.5 sec.

Solder Temperature: 245±5℃

Solder Wetting 95% of immersed area must show no voids, pin holes

6-10

Resistance to Soldering Heat

(DIP)

Solder pot method

Soldering time: 10±0.5 sec.

Solder Temperature: 260±5℃

Solder iron method

Soldering Time: 5±0.5 sec.

Solder Temperature: 370℃ ~ 400℃

Appearance No Damage.

6-11

Resistance to Soldering Heat (SMT)

When reflowing

Refer to paragraph 8

Solder iron method

Soldering Time: 5±0.5 sec.

Solder Temperature: 370℃ ~ 400℃

Appearance No Damage.

7. Actuator Insertion/Withdrawal Force

DIP&Single Row SMT [Unit : kgf] Dual Row SMT [Unit : kgf]

Circuits	At Initial		Circuits	At Initial
Circuits	Insertion (Max.)	Withdrawal (Min.)	Circuits	Insertion (Max.)	Withdrawal (Min.)
Single	0.30	0.03	Single	0.30	0.03
02	2.00	0.50	2X05	3.50	0.90
03	2.50	0.55	2X06	4.10	1.00
04	3.00	0.60	2X07	4.70	1.10
05	3.50	0.65	2X10	6.50	1.40
06	4.00	0.70	2X15	9.50	1.90
07	4.50	0.75	2X18	11.30	2.10
08	5.00	0.80	2X20	12.50	2.40
09	5.50	0.85	2X25	15.50	2.90
10	6.00	0.90
11	6.50	0.95
12	7.00	1.00
13	7.50	1.05
14	8.00	1.10
15	8.50	1.15

Our Services
1.Quality is life, we establish our brand step by step (high quality).
2.Competitive price.
3.Attractive package.
4.Fast Delivery.
5.Excellent after-sale service.1.Quality is life, we establish our brand step by step (high quality).
2.Competitive price.
3.Attractive package.
4.Fast Delivery.
5.Excellent after-sale service.
6.Feel free to join our team and establish business relationship between us.
7.Welcome to inquiry us and send you our catalogue to know what we have.
6.Feel free to join our team and establish business relationship between us.
7.Welcome to inquiry us and send you our catalogue to know what we have.

Hot Products

250V AC / DC 2.0mm Pitch PA66 Automotive Electrical PAD Connectors Double Row

Contact Us

RULETEAM CONNECTION TECHNOLOGY (SHENZHEN) CO.,LTD

DF13 wire to board connector terminals tin-plated Crimping Connector for Discrete wire AWG 30 to 26

Product Details

Hot Products

250V AC / DC 2.0mm Pitch PA66 Automotive Electrical PAD Connectors Double Row

Signal Connector SSHL Contact, 1.00mm Pitch SSHL Crimp Terminals for AWG#32 To 28 Wires

1A AC/DC PCB Connector Phosphor Bronze Contact, Gold-flash Crimp Terminals

SXH Connector Contact Pitch 2.50mm Brass or phosphor bronze terminals for AWG#22 - 28 wire

DF13 wire to board connector terminals tin-plated Crimping Connector for Discrete wire AWG 30 to 26

Tin-Plated / Gold-Flash Wire Connector Brass Crimp Terminals with 2.54mm Pitch