Mianyang Prochema Commercial Co.,Ltd.&GUS Industry (Hongkong) Co,.limited |
|
ETFE film plastic bag
Description
ETFE is a tough material, a variety of mechanical properties to achieve a good balance - anti-tearing strong, high tensile strength, medium hardness, excellent impact resistance, long telescopic life. ETFE is a good dielectric material, dielectric strength is high, the dielectric constant of 2.6, high resistivity, low dissipation factor, only 0.003. Its low dielectric constant, in the frequency and temperature changes in the case of basically constant. ETFE has a wide operating temperature range, a constant temperature range of -65 ° C to + 150 ° C, an ultra-low temperature toughness, and a brittle temperature of -100 ° C. In addition, ETFE also passed a number of stringent fire tests, such as IEEE 383, and UL 94 V-0 rating. For most of the chemical properties of the physical properties of small, ordinary gas and water vapor permeability is low.
Introduction of ETFE Membrane Material
Tetrafluoroethylene - Part 1: Chemical designation
Chemical name: ethylene - tetrafluoroethylene copolymer
Chemical English name: Ethylene tetrafluoroethylene
Technical Specification Code: 77
CAS No.:116-14-3
Molecular formula: C2F4
Molecular weight: 100.02
The critical pressure: 3.85Mpa, the critical density: 572kg / m3,
the vapor pressure at 25 ℃: 3.19Mpa, the vapor density: 572kg / m3,
the spontaneous combustion point: -142.5 ℃, boiling point: -78.4 ℃,
critical temperature: : 190 & lt; 0 & gt; C, pyrolysis
above 200 & lt; 0 & gt; C. HF decomposition and other toxic
gases.
ETFE Chinese name for the ethylene - tetrafluoroethylene copolymer.
ETFE film thickness is usually less than 0.20mm, is a transparent
membrane.
Ethylene-tetrafluoroethylene copolymer film as a crystalline
polymer having a melting point of from 256 to 280C. Olefin can be
self-extinguishing. Its high shear strength, low temperature impact
resistance is the best of the existing fluorine plastic, from room
temperature to-80 ℃ can have a higher impact strength, chemical
stability, electrical insulation and radiation resistance . The
actual use of ETFE film began in the 1990s, mainly as agricultural
greenhouse cover materials, various special-shaped buildings canopy
material, such as stadium grandstand, building cone top, casino,
revolving restaurant canopy, entertainment hall Covered, parking,
exhibition halls and museums. One of Britain's new millennium
projects, "Eden" has "the eighth wonders of the world" reputation.
It consists of four dome-shaped building connected the world's
largest greenhouse, covered with ETFE film material made of
transparent cover, its quality is only the same area of 1% of the
quality of glass, transparent flake can be recycled, and has good
insulation .
ETFE film is a superior quality alternative to transparent building
construction, which has been proven to be a reliable and economical
roofing material for many years in many projects. The film is made
of artificial high-strength fluoropolymer (ETFE), its unique
anti-adhesive surface so that it has a high resistance to dirt,
easy to clean features. Usually rain can remove the main dirt.
ETFE membrane life of at least 25-35 years, is used for permanent
multi-storey mobile roof structure ideal material. The membrane
material used for a span of 4 meters for two or three inflatable
support structure, but also according to the special engineering
geometry and climatic conditions, increasing the membrane span.
Membrane length to easy to install as a standard, generally 15-30
meters. Small-span monolayer structures are also available in
smaller sizes.
ETFE film to B1, DIN4102 fire rating standards, combustion will not
drip. And the film quality is very light, only 0.15-0.35 kg per
square meter. This feature makes it even in the smoke, fire caused
by the film melting also has considerable advantages.
Depending on the location and surface printing, the ETFE film has a
light transmittance of up to 95%. The material does not block the
transmission of ultraviolet light and other light to ensure that
the building interior natural light. By surface printing, the
translucency of the material can be further reduced to 50%.
According to geometric conditions and the number of layers of the
film, the K value can be as high as 2.0W / m2K. The energy
dissipation index can be as high as 0.77 with a three-layer printed
film.
Because of its excellent quality, ETFE film almost no daily
maintenance. A simple inspection of the roof due to mechanical
damage (once a year) is recommended and can be repaired as needed.
Also check the ventilation system, replace the filter device.
ETFE membranes are fully recyclable materials that can be reused to
produce new membrane materials or to separate other impurities to
produce other ETFE products.
National Olympic Natatorium Water Cube is made of ETFE film.
ETFE (F-40) fluorine plastic from the United States DuPont and
Japan's Asahi Glass Company, mainly used in anti-corrosion lining.
The material has polytetrafluoroethylene corrosion resistance
Features: light resistance, weather resistance, insulation resistance, flame resistance
Application: solar cell
Required characteristics: light resistance, weather resistance, insulation, etc.
Use of raw materials: ETFE (ethylene tetrafluoroethylene copolymer)
ETFE film, is now increasingly being applied to the solar industry, it is very suitable for the surface of the solar cell material.
ETFE film, has excellent mechanical strength and flame resistance, exposure of 3000 hours and still no change in mechanical properties. In the visible region, excellent light transmittance can absorb more light, in addition, the adhesion between it and the EVA is also very advantageous.
Our ETFE film is made by the complete set of imported equipment . It has the properties of anticorrosive ,weather fastness ,aging resistant ,Good radiation stability,nonstick, chemical stability ,dielectric insulation ,nontoxic and low crock etc.
It is widely used in the fields of Semiconductor ,LED ,FPC,flexible solar cell ,medical packing,construction ,Agriculture etc.
Surface treating ,matting treating,width cutting etc can be done based on buyer’s requirements.
ETFE FILM Series
Grade | Thickness (um) | Width (mm) | Weight kg/roll | Length (m) | Length tolerance (mm) | Color | Surface condition |
25C | 25 | 1250 | 54.7 | 1000 | +5,-0 | transparent | Glossy/Matt |
50C | 50 | 1250 | 54.7 | 500 | +5,-0 | transparent | Glossy/Matt |
75C | 75 | 1250 | 19.2 | 300 | +5,-0 | transparent | Glossy/Matt |
100C | 100 | 1250 | 54.7 | 250 | +5,-0 | transparent | Glossy/Matt |
150C | 150 | 1250 | 260+/-13 | 200 | +5,-0 | transparent | Glossy/Matt |
200C | 200 | 1250 | 350+/-17 | 150 | +5,-0 | transparent | Glossy/Matt |
250C | 250 | 1250 | 437+/-22 | 100 | +5,-0 | transparent | Glossy/Matt |
ETFE film Technical Data Sheet
Item | Unit | Data |
Specific Gravity | g/cm3 | 1.74 |
Melting point | oC | 260+/-10 |
Tensile strength | Mpa | >39.2 |
Tensile Elongation | % | 200-510 |
Tear Strength | N/mm | 170-250 |
Volume Specific Resistance | Q.cm | 1x1015 |
Linear Dimensional change | % | +/-5% |
General Properties of ETFE film
1.Can be used at hight temperature over 200oC
2.Can stop mold bleed
3.Excellent ensile and tear strength
4.Oustanding non-stick
5.Non-toxicity for envirenment
6.Non flammability
7.Chemical resistance .
8.Weather resistance
9.Solvent resistance
Note: If you need any products of ours, please kindly contact with us
directly by following contaction . Then we can reply you faster and
easy . Thanks
Chemical resistance
Chemicals | Chemical resistance | |
vitriol
| 78% | √ |
98% | √ | |
nitric acid | 25% | √ |
60% | √ | |
70% | √ | |
chlorine | √ | |
bromine | √ | |
chlorosulfuric acid
| √ | |
water | √ | |
carbon dioxide | √ | |
sodium hydroxide | 10% | √ |
50% | √ | |
Dihydroxyethyl Tallow Amine Oxide | 15% | √ |