Oridinary Competitive Price Pipe Threading Machine For 1/2inch To 2inch 750W 24RPM

Oridinary competitive price pipe threading machine for 1/2inch to 2inch 750W 24RPM
Pipe threading Machine
Pipe threading machine is applicable in cutting,carving thread and inner hole chamfering varieties inches tubes for purpose of water.electric and gas.
Keywords: bolt threading machine price,rod threading machine price, automatic threading machine price, threading machine manufacturers, metal threading machine, small threading machine, threading machine price, pipe threading machine, electric pipe threading machine, Iron pipe threading machine, steel pipe threader, stainless steel threading machine, pipe threading machine, electric pipe threading machine, 
 
Specification
Model: ZT-R2
Pipe Capacity: 1/2"-2"
Dies: 1/2"-3/4", 1"-2" BSPT/NPT
Spindle Speed: 25RPM
Motor: 220V/380V Universal Motor 50HZ
Power: 750W
Gross Weight: 86Kg
Packing Size: 750*550*580(mm)
 

Working principle of threading machine

Installation
1. Check if all parts and accessories are in good condition including tool bag, oil, tooth, tooth holder and support legs.
2. Lift the device and fix the legs, then tighten the screws of the legs evenly
The back head should be slightly higher than the hammer head to ensure the cooling oil flow.
3. Clean the oil from the teething and add some grease to the places of movement.
4. Make sure the machine is working properly before starting and make sure the oil is pumped.
5. Install each moving part when you want to move the machine to another work area. The dental head must be locked in place, and a short tube placed in the head.
 
Operation manual
1. Catch tubes
1) Expand the thread head to enter the tubes from the compressor shaft side.
2) At first close the rear head, then close the front head to catch the tubes, check the three jaws of the head from the front head and on normal use, jerk the knocking head toward yourself to lock the tube.
3) Move the front head in the opposite direction to unscrew the tube after completion.
4) If you are using a short tube so that it does not reach the back jaw, just insert the tube towards the head of the teeth and lock it with the teeth, then insert the supporting head to fix the tube.
2. Teething
1) Lift the cutter out of the way and bring the tooth head into the working position.
2) Turn on the switch to make the machine work. Apply pressure to the sliding handle until three or four threads are cut. Then release the sliding handle, the normal teething will be cut off automatically. When an appropriate amount of placements are cut.
3. Tube cutting
1) Put the pipe cutter in the working position.
2) Turn the sliding handle to make the pipe cutter to the point you want to cut.
3) Turn the cutter handle tightly.
4) Turn on the switch. Then turn the cutter handle slowly and tightly as it cuts from the tubes.
5) After cutting the tubes, release the cutter handle and raise the tube cutter.
4. Enlargement
1) Make the lathe head in the working position.
2) Lock the lathe head.
3) Turn on the switch. Adjust the slide knob to bring the lathe head into the tubes.
4) Cut off the electricity. Return the lathe head to its normal position

 
Application & Details:

 

 

Our service:
1. How to get a accurate quotation from us?
Provide us the detail of the material such as metal thickness and width.
2. What’s the shipping cost from China to your country?
We can send machine to your port or door address by sea or airplane. Please kindly tell us your nearest port or address with postcode.We have reliable shipping agent to insure the safe, convenient and timely delivery.
3. Payment terms, MOQ, warranty, FOB?
Payment terms: 30% TT paid in advance, the balance of 70% before the shipment.
Minimum order quantity: 1 set.
FOB :Shanghai.
Delivery time :7 days after receipt of formal order and 30% deposit.
Warranty:12 months.
4. What’s the package?
Fumigation-free plywood case or without package.
5. What about commissioning service?
We can offer commissioning service, the buyer need to afford plane tickets.
6. What’s policy for guarantee and broken parts?
Warranty period of equipment lasts a year, during which the broken parts and spares caused by quality can be offered free.
7.Any question, call us or send email, we will try our best to satisfy you.