Wu Han Micro Control Electric Co., Ltd. |
|
Web Control Intelligent Tension Meter For Tension Load Cell In Flim Printing Machine
Features:
1. 32 Bit CPU guarantees high speed,precision,anti-jamming
capability and ensures reliability.
2. The outside has no adjustable potentiometer.
3. 0~10V /0~5V and 0~20ma/4~20ma output signals can be free to
choose.
4. Use dispensing technology, small volum,light weight.
5. Mosaic installation,simple and convenient.
Attention:STM-050 tension meter only display tension,no control signal output,other functions same as STM-10PD.
Parameters | |
Model | ST-10PD |
Power Supply | DC 24V |
Input Analog singal | 1. L+~L-;R+~R-;Left,right tension loadcell signal input |
STS tension loadcell signal (0~200mv,power supply DC5V) | |
STSA tension loadcell signal(0~15mv;power supply DC5v) | |
Control output | 1. Vout-GND:DC0~10V/0~5V |
2. Iout-GND:DC0~20mA/4~20mA | |
(STM-050 without Vout,Iout output) | |
Tension Display | L+R Total tension L: left tension R:right tension |
Fixed output | 5V+-GND:DC5V tension loadcell power supply |
Outline size | 96*48*109mm |
Electrical Wiring
L+:positive terminal of tension detector input signal on left side
L-:negative terminal of tension detector input signal on left side
5V+:positive terminal of tension detector power supply on both sides
PE:detector shielding cable on both sides
GND:power supply negative terminal on both sides
R+: positive terminal of tension detector input signal on right side
R-:negative terminal of tension detector input signal on right side
STS sensor wiring
Iout: 0~20mA output
Vout: 0~10V output
5V+: 5V output
GND: output negative terminal of voltage and current
NOTE:
(1) If STM-10PD tension meter install STS Differential sensor by wuhan true engine company ,wiring colors as follows :
(2) If STM-10PD tension meter install STSA Strain-gauge sensor by wuhan true engin company ,wiring colors as follows :
“5V”—red “GND”—black, “Terminal +”—green, “Terminal-”—white,
(3) If only use one tension sensor,please use wires to connect L+ with R+,L- with R-.
“5V”—red “GND”—black, “Terminal +”—green, “Terminal-”—white,
Using steps
1. Enter C11 ,according to the tension sensor type to set C11
parameter value:if it is differential sensor,the value is set to
0,if it is strain gauge sensor,the value is set to 0.
2. When use the tension meter output to participate the control
with PLC ,according to the actural need to set C09/C10.
3. Set the alarm value when it is needed,otherwise it has no alarm
with 0.0kg.
4. According to the actual need to set C04 full degree of
tension,its value should be 20%~80% of tension sensor rated range.
Notes for use
1. Set screw should not be too long when the bearing hourses are
installed on the detector.
2. Use spherical universal bearing hourses.
3. The wrap angle of film over detector reel should not be larger
than 120 around 60 would be perfect.
4. The load force caused by film tension should not point to he
screw ends of tension detector.
5. The screw ends of tension detector should point upwards when
installed on a wall.
6. If the force caused by film tension pulls but not pushes the
tension detector,so the negative and positive detector signal wires
should exchange when connected to the tension meter.
FAQ
1. How to place an order?
Please provide us more details of what you want, such as:
application, measurement range, output, accuracy, thread type,
electric connector and other related parameters.
2. Does SNC offer any discount?
Yes, if you buy large QTY, please contact us, we will give you a
big discount.
3. What terms of payment are available?
We accept T/T, L/C, Trade assurance, Western Union, Paypal, etc.
4.When will you arrange the production?
We will arrange the production immediately after receiving your
payment.
5. How do you ensure good product quality?
We have a complete quality control system, all of our products are
fully checked by IQC, OQC departments before shipping to our
clients
6. Do you have warranty ?
Yes, we provide 2 years warranty for most of our products.