Allen Bradley Modules 1756-L1M2 1756 L1M2 AB 1756L1M2 PROCESSOR UNIT superior quality product

Allen Bradley Modules 1756-L1M2 1756 L1M2 AB 1756L1M2 PROCESSOR UNIT superior quality product

Product Description:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

Related Product Recommendation:

Product's Character:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

1745-C2 Interconnect Cable AB
1745-C2 B Interconnect Cable, Series B AB
1745-C3 SLC 150 Interconnect Cable AB
1745-C3 A SLC 150 Interconnect Cable, Series A AB
1745-E101 Expansion Unit AB
1745-E102 Expansion Unit AB
1745-E103 Expansion Unit AB
1745-E104 Expansion Unit AB
1745-E105 Expansion Unit AB
1745-E106 Expansion Unit AB
1745-E107 Expansion Unit AB
1745-E151 SLC 150 Expansion Unit AB
1745-E152 SLC 150 Expansion Unit AB
1745-E153 SLC 150 Expansion Unit AB
1745-E154 SLC 150 Expansion Unit AB
C SLC 150 High Speed Input Module AB
1745-E156 SLC 150 Expansion Unit AB
1745-E157 SLC 150 Expansion Unit AB
1745-LP101 Processor Unit AB
1745-LP102 Processor Unit AB
1745-LP103 Processor Unit AB
1745-LP104 Processor Unit AB
1745-LP151 SLC 150 Processor Unit AB
1745-LP152 SLC 150 Processor Unit AB
1745-LP153 SLC 150 Processor Unit AB
1745-LP154 SLC150 SLC 150 Processor Unit AB
1745-LP156 SLC 150 Processor Unit AB
1745-LP157 SLC 150 Processor Unit AB
1745-M1-- EEPROM Memory Module AB
1745-PCC SLC Personal Computer Interface Converter AB

1745-PT1 Hand Held Programmer AB
1745-TCAT TCAT SLC-100 Timer Counter Access Terminal AB
1746-A10 10-Slot Chassis AB
1746-A13 13-Slot Chassis AB

The use of the product: