Home Companies Chongqing Dongchong Aluminum Co., Ltd.

Cosmetic Shell H18 1070 Color Coated Aluminum Sheet

Active Member

Contact Us

[China]

Address: D41-1/01 BLOCK,D FENQU,XIPENG ZUTUAN,XIANGTANG VILLAGE,XIPENG TOWN,JIULONGPO DISTRICT,CHONGQING

Contact name:Masha Cui

Chongqing Dongchong Aluminum Co., Ltd.

Cosmetic Shell H18 1070 Color Coated Aluminum Sheet

Country/Region	china
City & Province	chongqing chongqing
Categories	Aluminum Sheets

Product Details

1000 x 2000 1070 H 18 Color Anodized Aluminium Alloy Sheet For for Cosmetic Shell 0.01~2.00 mm

Product Description

After anodizing, the surface of the aluminum can produce a few microns-hundreds of microns of oxide film. Compared with the natural oxide film of aluminum alloy, its corrosion resistance, wear resistance and decorative properties have been significantly improved and improved. In fact, the direct current sulfuric acid anodic oxidation method is the most common application, because it is suitable for aluminum and most Anodizing of aluminum alloy; thicker film, hard and wear-resistant, better corrosion resistance after sealing; film colorless and transparent, strong adsorption capacity, easy to color; lower processing voltage, less power consumption ; The treatment process does not need to change the voltage cycle, which is conducive to continuous production and practical operation automation

1070 aluminum has the characteristics of high plasticity, corrosion resistance, good electrical conductivity and thermal conductivity, but low strength, not strengthened by heat treatment, poor machinability, and can accept contact welding and gas welding. Make full use of its advantages to manufacture some structural parts with specific performance, such as gaskets and capacitors made of aluminum foil, tube isolation nets, protective sleeves for wires, cables, nets, cores and aircraft ventilation system parts and decorative parts.

Chemical Composition

ALLOY	CHEMICAL COMPOSITION (%)
ALLOY	Si	Fe	Cu	Mn	Mg	Cr	Ni	Zn	Ti	Zr	Other		Al
3003	0.6	0.7	0.05-0.2	1.0-1.5				0.1			0.05	0.15	rest
3004	0.3	0.7	0.25	1.0-1.5	0.8-1.3	__	__	0.25	__	__	0.05	0.15	rest
3104	0.6	0.8	0.05-0.25	0.8-1.4	0.8-1.3	__	__	0.25	0.1	__	0.05	0.15	rest
3105	0.6	0.7	0.3	0.3-0.8	0.2-0.8	0.2	__	0.4	0.1	__	0.05	0.15	rest
5052	0.25	0.4	0.1	0.1	2.2-2.8	0.15-0.35	__	0.1	__	__	0.05	0.15	rest
5A06	≤0.40	0.000～0.400	≤0.10	0.50～0.8	5.8～6.8	__	0.0001～0.005	≤0.20	0.02～0.10	__	0.05	0.1	rest
5005	0.3	0.7	0.2	0.2	0.5-1.1	0.1	__	0.25	__	__	0.05	0.15	rest
5050	0.4	0.7	0.2	0.1	1.1-1.8	0.1	__	0.25	__	__	0.05	0.15	rest
5154	0.25	0.4	0.1	0.1	3.1-3.9	0.15-0.35		0.25	0.2		0.05	0.15	rest
5754	0.4	0.4	0.1	0.5	2.6-3.6	0.3	__	0.2	0.15	__	0.05	0.15	rest
5454	0.25	0.4	0.1	0.5-1.0	2.4-3.0	0.05-0.2		0.25	0.2		0.05	0.15	rest
5182	0.2	0.35	0.15	0.2-0.5	4.0-5.0	0.1		0.25	0.1		0.05	0.15	rest
5083	0.4	0.4	0.1	0.4-1.0	4.0-4.9	0.05-0.25	_	0.25	0.15	__	0.05	0.15	rest
5086	0.4	0.5	0.1	0.2-0.7	3.5-4.5	0.05-0.25		0.25	0.15		0.05	0.15	rest
6060	0.3-0.6	0.1-0.3	0.1	0.1	0.35-0.6	0.05		0.15	0.1		0.05	0.15	rest
6061	0.4-0.8	0.7	0.15-0.4	0.15	0.8-1.2	0.04-0.35	__	0.25	0.15	__	0.05	0.15	rest
6063	0.2-0.6	0.35	0.1	0.1	0.45-0.9	0.1	__	0.1	0.1	__	0.05	0.15	rest

Aluminium Material Grade

1)1000series aluminium /Pure Aluminum/Pure Aluminium:1050,1060,1070,1080,1100,1350,etc

2)2000series aluminium alloy/Hard Aluminum/Hard Aluminium/Aluminum-Copper Alloy/ Aluminium-Copper Alloy:2011,2014,2017,2024,etc

3)3000series aluminium alloy/ Rust-Proof Aluminum/Rust-Proof Aluminium/ Aluminum-Manganese Alloy:3002,3003,3104,3204,3030,etc

4)5000series aluminium alloy/ Rust-Proof Aluminum/Rust-Proof Aluminium /Aluminum-Magnesium Alloy:5005,5025,5052,5040,5054,5056,5083,5152,etc

5)6000series aluminium alloy / Aluminum-Magnesium-Silicon Alloy /Aluminium-Magnesium-Silicon Alloy /:6101,6003,6061,6063,6020,6201,6262,6082,etc

6)7000series aluminium alloy/ Aluminum-Zinc Alloy/ Aluminium-Zinc Alloy:7003,7005,7050,7075,etc

7)8000series aluminium alloy:8011,etc

Mechanical properties:

Tensile strength σb (MPa) )≥75

Conditional yield strength σ0.2 (MPa) )≥35

Product Photo

Company Introduction

Chongqing Dongchong Aluminum Co,.Ltd.established in 2002 and have been in aluminium indurstry for more than 17 years.After more than ten years of rapid development, it now has more than 100 employees, more than 15,000 square meters of standard factory buildings and more than 2,000 square meters of office area.

The evelopment concept of corporate Innovation and Practicality Beyond Self-Pursuing Excellence. Dongchong's Mission is While creating value for the society, we should take effective measures to increase employees'income, make them have more time and wealth to control, and constantly improve employees' happiness index. Our business philosophy is Honesty, Cooperation and Win-win .Service Concept is "It is our duty to satisfy all our customers.It's our task for all our customers to praise Dongchong".

We mainly provide Aluminum Alloy Sheet ,Aluminum Circle Sheet ,Diamond Aluminum Sheet ,Aluminum Flat Strips ,Aluminum Alloy Plate,Aluminum Foil ,Aluminum Checker Plate,Aluminum Coil Strip ,Aluminum Hollow Pipe ,Aluminum Extrusion Profiles ,Custom Aluminum Panels ,Aluminum Solid Bar ,Aluminum Cabin Luggage.

Equipment Production Parameters By Chongqing Dongchong Aluminum Co.,Ltd
1650mm Slitting machine	Uncoil(MM)				Finished size(MM)		Slitting Width(MM)
	ID	OD	Width	Thickness	ID	OD	Above 0.5mm≥ 20mm
	Φ 400	≤ 1800	≤ 1600	0.5-4.5	Φ 400	≤ 1700(normal)
	Φ 500				Φ500(normal)
	Φ 600
Aluminum foil Slitting machine	Uncoil(mm)				Finished size(MM)
	ID	OD	Width	Thickness	ID	OD	Width
	Φ 76	≤ 550	≤ 1200	0.08-0.12	Φ76Φ76	≤ 550(normal)
1450mm Crosscutting machine	Uncoil(MM)				Finished size(MM)
	ID	OD	Width	Thickness	ID	OD	Width
	Φ 505	≤ 1780	≤ 600	0.1-1.5	Φ150 Φ300 Φ400 Φ500	≤ 1700(normal)	6-600
	Φ 605
Annealling Furnace	Furnace Temperature		Furnace Size
	≤440°C		320020002100
Saw Cutting	Thickness(mm)		Width (mm)			Length (mm)
	Size		Size		Tolerance	Size
	≤200		≤2000		±0.3	≤3000
Embossing Machine	Type	Thickness(MM)	Width(MM)	Embossing height(MM)	Tolerance(MM)	Type	Thickness(MM)
	Single side ball	0.3-1.0	≤700	≤3	±0.1	two-side ball	0.3-1.0