Results for101 6mm length test finger probefrom 30015 Products.
|
|
IEC61032 Figure 17 Test Bar 43 Product information: This test bar 43 confirms to the IEC61032 figure 17 and IEC60335 standard requirements. It is used for testing the protection of ...
|
|
|
|
|
Wedge Probe For Document Shredder The wedge probe is one of two new accessibility probes required by UL 60950 for paper shredders. UL found that children and small women could ...
|
|
|
|
|
Product Description The Rigid Test Finger is a precision test probe made according to Figure 7 (Fig. 7) of the IEC 61032 (Test probe 11) and is used to simulate a human finger. It ...
|
|
|
|
|
IEC60065 Test Hook for Audio and Video Made by 304 Stainless Steel 1. Introduction The test hook is designed according to IEC60065 clause 9.1.7 and figure 4. It is mainly applied ...
|
|
|
|
|
UL1278 Fig 10.2 Bar Probe Product details: It conforms to standard requirement of UL1278 Fig 10.2. The handle is made of nylon and the probe is made of stainless steel. Standard...
|
|
|
|
|
Rigid Finger 1 Ø50mm, 20mm wide, 100mm long
|
|
|
|
|
IEC60529 Stainless Steel 2.5mm Test Rod for IP3 and suffix C code Test Introduction: The 2.5mm Test Rod is used to verify the protection of persons against access to hazardous ...
|
|
|
|
|
Figure 58.5 Test Probe Product details: It conforms to the standard of UL499 Fig 6.4 and UL982-2006 Fig 58.5(PA190). It is applicable for the electrical equipment. The handle is ...
|
|
|
|
|
UL Enamel Wire Probe 25 Usage: This probe is use to checking access to enamel coated wire accord to UL standard requirement. stainless steel with stainless stell handle.
|
|
|
|
|
Abration Resistance Test Pin Made by Hardened Steel Conforms to IEC60950 1. Introduction The scratch resistance test uses a hardened steel pin for scratching. The end of the steel ...
|
|
|
|
|
UL398 Fig 8.2 Probe for Film-coated Wire Product information: This probe conforms to standard requirement of UL398 Fig 8.2(PA170B),UL507(PA170D),UL749 Fig 2,UL982 Fig 58.6 and ...
|
|
|
|
|
IEC 60529 Test Sphere50mm , IP1X This probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
IEC60335-2-80 Figure 102 Test Pin for Testing the Fan 1. Introduction The test pin is completed designed according to IEC60335-2-80 figure 102, it is to simulate the bolt of fan. ...
|
|
|
|
|
Test Plug For Mechanical Tests On Antenna Coaxial Sockets Product information: This test plug conforms to IEC60065 Figure 8 standard requirement. It is used to test the antenna ...
|
|
|
|
|
Test Rubber Ball Usage rubber ball used for dynamic stability testing to UL (USA) standards. A ball, 2 and 3/4/16 inch diameter (2.187 inches), filled with No. 60 core sand. It is ...
|
|
|
|
|
IEC60335-2-14 Stainless Steel Test Probe Product information: The stirrer shall incorporate a biased-off switch that is recessed or guarded to prevent accidental operation. It ...
|
|
|
|
|
Antenna coaxial sockets mounted on the apparatus Antenna coaxial sockets mounted on the apparatus and incorporating parts or components which isolate HAZARDOUS LIVE parts from ...
|
|
|
|
|
IEC60335-2-14 Stainless Steel Test Probe Product information: The stirrer shall incorporate a biased-off switch that is recessed or guarded to prevent accidental operation. It ...
|
|
|
|
|
IEC 60529 Test rod 2.5mm, IP3X Usage This wire is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
IEC60335-2-24 Figure 102 Scratching Tool Tip Product information: The scratching tool tip is for home appliances whose accessible element surface of all protected cooling system, ...
|
|
|
