200L Nutsche filter dryers
TOPTION brand 200L nutsche filter dryers gather “Filtration,
Washing, Drying” function in one body, which is a new premium
solid-liquid separation technology, can make the material finish
filtering, washing and drying process in an airtight container
equipment, utmost to improve the utilization rate of the nutsche
filter dryers.
Technical parameters of 200L nutsche filter dryers
Name | DN600 Nutsche filter dryers |
Item No | RFCD-DN600-316L | | |
Container Diameter | 600mm | thickness | 6mm |
Filter Area | 0.28m2 | Volume | 0.2m3(200liter) |
Design Pressure | 0.4Mpa for container | 0.5Mpa for jacket |
Design Temperature | 130℃ for container | 150℃ for jacket |
Material | material-contacting parts:SS31603; Others: SS30408 |
Filter type | 316L sintering net | Micron size | 10 micron |
Main Shaft seal way | Packing seal way | Material | PTFE packing |
Agitation blade | S-shaped asymmetric paddle |
Shaft lift height | 100mm |
Mixing stroke | 200mm |
Stirring motor power | 1.5kw EX Motor |
Explosion proof grade | dⅡBT4 |
Stirring speed | 0~20r/min |
Stirring lift type | Hydraulic Cylinder Drive |
Chassis lift type | Hydraulic Cylinder Drive |
Discharge port switch form | Hydraulic Cylinder and Hydraulic Motor Drive |
Hydraulic motor power | 1.5kw |
Voltage | 3 phase 380V 60HZ |
Why choose nutsche filter dryers ?
1. In one same container finish filtering, washing and drying whole
process, continuous operation.
2. Operate under pressure or vacuum condition, realize the
solid-liquid separation.
3. During filtering process, the filter cake uniform distribution,
solid-liquid separation effect is good.
4. Hydraulic pressure control the rise & fall of the mixing
system, has uttermost increase the solid materials space during
filteration process.
5. The rise & fall and stirring of mixing blade, make the
cleaning fluid and filter cake intensive mixing during washing
process , guarantee the filter cake full washing.
6. Greatly shorten time during drying process, improve efficiency.
7. Various control of liquid outlet valve, automatic material
discharging of solid discharging system, reduce the labor
intensity, save cost and more efficient.
8. Can washing online, sterilization online, all operation process
can be done under inert gas protection, safe and reliable.
9. Nutsche filter baseplate is removable, help the equipment
realize thoroughly cleaning, applicable to the production of
sterile bulk drug, full compliance with GMP and FDA production
requirements.
Nutsche filter dryers factory show, CE certification, ISO approved, quality is our culture, welcome
contact info@toption-china.com for professional customize or factory visit.
Lab type nutsche filter
Nutsche Filter Dryer
In order to meet the confined production process, filter washing
and drying reactor, three-in-one filter has been developed.
TOPTION this production system can realize half automatic or
complete automatic operation control.
Nutsche Filter Dryer main working steps
1. Feeding
Open the feeding valve to feed in the tank, paddle should be in the
upper position when feeding, if necessary, can be lowered stirring
paddle for low speed stirring, so that the material is evenly
distributed. When the material reaches the specified process stop
feeding, close the feed valve.
2. Washing
Washing fluid at 0.2 ~ 0.3MPa pressure by the rotating nozzle
cleaning, and stirring paddle has been suspended high.
3. Filter
After washing, upper the stirrer to related position, stop
stirring, the liquid will be discharged from bottom. Then repeat
the filtering steps until you get perfect material.
4. Drying
- Open hot water valve, then balance valve, next vacuum valve.
- Please open the balance valve in advance if upper vacuum down
drying condition, to ensure pressure balance. to Concentration of
chloride ions in the heating and cooling water should be strictly
controlled, to avoid chloride ions on the jacket and the tank
corrosion. Please use of chloride-free water.
- Open the jacket water inlet valve slowly, and open slightly for
water outlet valve. Fully open them when outlet and inlet has
temperature gap less than 20℃ to avoid cavitation vibration.
5. Material discharge
Sampling analysis before discharge, if ok, then discharge them.
- Nutsche filter dryer
Main technical parameters of laboratory nutsche filter:
No | Details | Remark |
1 | description | Filter area | 0.07m2 | |
filtering accuracy | 5μm | Standard 5um 1um-2mm is optional |
Inner diameter | 300mm | |
volume | 0.02m3 | |
Empty weight | 600kg | |
Total height | 1700mm+150mm | |
Tank design pressure | -0.1~0.4MPa | |
Jacket operation pressure | 0.5MPa | |
Tank operation temp | 0~160℃ | |
Jacket operation temp | 0~160℃ | |
Tank working medium | Chemical materials | |
Jacket working medium | Cooling water, hot water, hot oil, steam | |
Heating position | Tank(jacket), bottom (jacket) | |
Discharge method | Manual side discharge | |
Pressure tank design standard | GB150.1~150.4-2011 | |
Flange design standard | HG20592-2009 | |
Clamp design standard | ISO2852 | |
Discharge valve port size | 100 | |
Discharge port size | 50 | |
2 | Mixing drive apparatus | Stirrer stroke | 100mm | |
Stirrer motor power | 1.1kw | |
voltage | 220 V | |
Rated frequency | 50Hz | |
phase | 2 | |
Max rotation speed | 15rpm | |
Min rotation speed | 0rpm | |
3 | main configuration list | O shape seal | Coaded with PTFE | |
Gear motor | Eugene | |
Reducer | 1:100 Reduction ratio | |
Machinery Seal | Mechanical seal, wetted material 316L, + bellows | |
Spray ball | Fixed type, 1 pc, SS316L | |
More nutsche filter customize, want to know detail information of
nutsche filter dryer, welcome contact info@toption-china.com 24h/7days online service.