|
[China]
Trade Verify
Address: 1st Floor, Zhigu, No. 2-10, South jinlong Avenue, Shahu Community, Biling Street, Pingshan District, Shenzhen, China
Contact name:Keira
Shenzhen Wonsun Machinery & Electrical Technology Co. Ltd |
|
Verified Suppliers
|
|
|
8sec DC24V Brushless Motor Parking Barrier Gate Arm Swing out Parking Lot Management
1. Selection of spring
The spring is stretchable one and
the specification is as follows:
Diameter 4.0MM green color
Diameter 4.5MM red color
Diameter 5.5MM blue color
Diameter 6.8MM yellow color
Diameter 7.0MM white color
When setting the function, please press the menu button on the control panel. The Nixie tube displays H00-00 or H00-other numbers. We correspond to the function parameter table code to enter the required function parameter setting. For example, H00-00 is the UP ARM speed adjustment, and then press the confirm button Enter the parameter setting, the number will be displayed on the digital tube, then press the up or down key to set the required UP ARM speed number, and then press the confirm button to complete the ARM-up speed setting.
The other function settings are the same as the example settings.
3.1 The running speed can be adjusted from 2.5s to 8s
3.2 Arm can be quickly interchanged.
3.3 Open the barrier gate by motor wheel when power off ,automatically reset after power on
3.4 Curved crank arm three- link movement structure, the operation is stable
3.5 Wireless remote control control open/close
3.6 Auto reverse function(force adjustable)
3.7 Infrared photocells connector is available
3.8 Loop detector connector is available.
3.9 Well-integrated with car parking system equipment,with wire control(must be switch signal)
3.10 Connector for traffic light(AC220V,power less than 40W)
3.11 Offering dry contact signal for car parking system(COM,NC,NO)
3.12 Auto-delay when closing(adjustable)
3.13 RS485 or CAN network communication interface(no need to install module)
3.14 Counting interface
3.15 24V backup battery interface(Can be charged by using solar energy)( optional)
3.16 Arm open when power off ( add backup battery) (Optional)
3.17 Anti-collision alarm device
4.1 Working temperature(motor): -30℃~+70℃
4.2 Rated voltage:DC24V
4.3 Running speed:2.5s-8s
4.4 Rated current:9.5A
4.5 Rated power:150W
4.6 No-load speed:1850rpm
4.7 Rated speed:1400rpm
4.8 Rated torque:59.6N.m
4.9 Relative humidity:≥85%
4.10 Remote control distance:≤100M(in the open place)
4.11 IP Degree:IP44
4.12 Max length of arm:6M
5.The parameter for selecting the spring
| Arm type | Arm length | Use of spring | |
| Type | Dimension(Wire Diameter*Length) | ||
| 100*45 Straight arm | 6m | Tension spring | 4.5+5.5 |
| 5m | 4.0+5.5 | ||
| 4.5m | 4.5+4.5 | ||
| 4m | 4.5+4.0 | ||
| 3.5m | 4.5 | ||
| 3m | 4.5 | ||
| 80*45Straight arm | 6m | 5.5+4.0 | |
| 5m | 5.5+4.0 | ||
| 4.5m | 4.5+4.5 | ||
| 4m | 4.5+4.0 | ||
| 3.5m | 4.5 | ||
| 3m | 4.0 | ||
| Two fence arm | 4.5m | 5.5+5.5 | |
| 4m | 4.5+5.5 | ||
| 3.5m | 4.5+4.5 | ||
| 3m | 4.5+4.5 | ||
| 90 degree arm | 5m | 5.5+4.5 | |
| 4.5m | 5.5+4.5 | ||
| 4m | 4.5+4.5 | ||
| 3.5m | 4.5+4.5 | ||
| 3m | 4.5+4.0 | ||
| Three fence arm | 4.5m | 5.5+6.8 | |
| 4m | 5.5+5.5 | ||
| 3.5m | 4.5+5.5 | ||
| 3m | 4.5+4.5 | ||
| Remark:6.8 yellow,5.5 blue,4.5 red,4.0 green | |||
6.Function setting parameter table
| Menu code | Parameter Scale | Parameter name | Default | Unit | Remark | |||
| H00-00 | 25-95 | Open speed adjustment | 40 | Corresponding PWM duty cycle 25%-95%, step size is 1 | ||||
| H00-01 | 25-95 | Close speed adjustment | 40 | Corresponding PWM duty cycle 25%-95%, step size is 1 | ||||
| H00-02 | 5-40 | Open in place decelerate angle | 35 | The larger the angle value, the less likely it is to shake the arm when it is in place. | ||||
| H00-03 | 5-40 | Close in place decelerate angle | 35 | The larger the angle value, the less likely it is to shake the arm when it is in place. | ||||
| H00-04 | 1-20 | Open accelerate adjustment | 1 | ms | The smaller the number, the faster the speed | |||
| H00-05 | 1-20 | Close accelerate adjustment | 8 | ms | The smaller the number, the faster the speed | |||
| H00-06 | 1-30 | Open in place angle | 1 | degree | step size is 1, when big than 11, will automatically check one side | |||
| H00-07 | 1-30 | Close in place angle | 1 | degree | step size is 1 | |||
| H00-08 | 7-13 | Auto reverse force adjustment | 10 | A | step size is 1 | |||
| H00-09 | 0-90 | Delay closing adjustment | 0 | second | step size is 100；0 is not closing automatically,Other value will be closing automatically; This parameter is for the situation that there is no loop detector signals and non-automatic operation occasions | |||
| H00-10 | 10-50 | Self-check speed adjustment | 30 | Corresponding PWM duty cycle 10%-50%, step size is 1 | ||||
| H00-11 | 0-2 | Self-check mode | 0 | 0:no operate automatically；1:operate automatically, eliminate after power off；2:operate automatically,Power failure memory.3.intelligent automatically operation. | ||||
| H00-12 | 0-5 | Self-lock force adjustment | 0 | 0:Invalid , 1or 2 valid | ||||
| H00-13 | 1-20 | Motor deceleration time when paused | 5 | The larger the setting, the longer the pause time will take | ||||
| H00-14 | 0-1 | Bid-direction setting | 0 | 0:Closing,1:opening | ||||
| H00-15 | 0-2 | Energy saving closing arm direction | 0 | 0:invalid 1:close arm valid(energy saving voltage is determined by 49 items ) 2:open arm valid | ||||
| H00-16 | 1-32 | RS485communication address | 1 | Up to 32 slaves can be connected | ||||
| H00-17 | 0-2 | RS485communication rate | 0 | 0:9600,1:19200,2:38400；Change the parameter and will be valid after power on again. | ||||
| H00-18 | 0-2 | Whether to self-check when power on | 1 | 0:no self-check,1:self-check；2:self-check with remote control; | ||||
| H00-19 | 0-3 | self-check setting | 2 | 0:Manually invalid,1:Keyboard SET button,2:remote control valid,3,Keyboard SET button and remote control both valid | ||||
| H00-20 | 0-15 | Monitoring parameter setting index | 7 | 0 | 0XD000 | Rotate speed | 0~2500 | |
| 1 | 0XD001 | Motor feedback angle | 0~90 degree | |||||
| 2 | 0XD002 | Busbar voltage(V) | 0~40.0 | |||||
| 3 | 0XD003 | Current output | ||||||
| 4 | 0XD004 | Hall state | 0~7 | |||||
| 5 | 0XD005 | Commutation number | ||||||
| 6 | 0XD006 | Total number of trips | ||||||
| 7 | 0XD007 | Run time(ms) | 0~9000 | |||||
| 8 | 0XD008 | Cumulative running times | 0`99999999 | |||||
| 9 | 0xD00A | Time of automation operation | 0~99999999 | |||||
| 10 | 0xD00C | Time of anti-Collision | 0~99999999 | |||||
| 11 | 0xD00E | The number of times of the arm is close in place | 0~99999999 | |||||
| 12 | 0xD010 | Power on time(minute) | 0~99999999 | |||||
| 13 | 0xD012 | Power supply power on times | 0~99999999 | |||||
| 14 | 0xD014 | Running status | Binary display | |||||
| 15 | 0xD015 | Fault code | 0~7 | |||||
| 19 | Number of UP arm | 0-65535 | ||||||
| 20 | Number of DOWN arm | 0-65535 | ||||||
| 21 | Number of STOP | 0-65535 | ||||||
| 22 | Number of Loop detector | 0-65535 | ||||||
| 23 | Number of Photocell | 0-65535 | ||||||
| 24 | Number of Camera | 0-65535 | ||||||
| H00-21 | 0-3 | Factory data reset | 0 | 1:Factory data rest,2:cumulative number of times cleared 3:Accumulate the number of times to clear and restore factory settings, return to 0 after execution | ||||
| H00-22 | 0-1 | Start acceleration time constant | 0 | The higher the value, the slower the acceleration | ||||
| H00-23 | 12-30 | Minimal output | 10 | Minimum output duty cycle of UP/DOWN arm | ||||
| H00-24 | 12-30 | STOP key function setting | 0:whenever you press pause, ARM stay in the current state 1:when close arm, press the STOP key to switch the arm to up command | |||||
| H00-25 | 1-20 | Reserve | ||||||
| H00-26 | 0-1 | Camera count timeout(seconds) | S | 0:count cleared when10 minutes time out, Not 0 is timing close arm | ||||
| H00-27 | 0-1 | |||||||
| H00-28 | 0-3 | LED light output mode | 0:Do not flash alternately during operation；1:Allow flashing; 2:Green light when UP arm on 45 Degree | |||||
| H00-29 | 0-2 | Multi function count input | 0:no counting function 1:UP counting 2:Counting input 3:directly stop when the alarm input is valid 4:when the alarm input is valid, it only prompts the alarm, and run normally | |||||
| H00-30 | 0~1 | DO1 functional output | 0:UP in place 1:DOWN in place 2:UP&DOWN in place 3:Fault input alarm(valid when 29 item set to 1) | |||||
| H00-31 | DO2 functional output | 0-5 | ||||||
| H00-32 | DO3 functional output | |||||||
| H00-33 | 485 communication status control | 485 communication, analog input port data | ||||||
| H00-34 | Peak pattern | 0-1 | Long press remote control whether to prohibit the use of IO port; 0: No prohibition effect; 1: effective | |||||
| H00-35 | Peak status | 0 | 1 or 2 :Peak pattern is effective,3:close loop detector function (setting it when 34 item is valid) | |||||
| H00-36 | Beeper setup | 0 | 0:close 1:effective | |||||
| H00-37 | Single stroke setting | 500~1000 (In bilateral detection, see item 6 of monitoring parameters. In bilateral detection, parameters are invalid.) | ||||||
| H00-47 | Motor type setting | 0:Gear 1:Turbine vortex rod 2:Advertising machine | ||||||
| H00-48 | Loop detector detect time constant | The smaller the setting, the more sensitive it is to the loop detector | ||||||
| H00-49 | Energy-saving voltage of UP&DOWN arm | 18.0~23.0V; over-setting will not work properly when power off | ||||||
| H00-50 | The delay time of closing arm when loop detector invalid | how long is the delay after turnover is in place, then close arm again | ||||||
Wonsun is a professional manufaturer for barrier gate, boom
barrier, sliding gate motor. If any interest, please contact me
freely.
Email: keira@wonsunbarrier.com
Skype: zimin1314
Whatsapp: +86 185 0748 1610
Wechat: Keira_Xia
Intearking Barrier Gate 6m Arm with DC24V Brushless Motor For Parking lot SYSTEM
