|
[China]
Trade Verify
Address: Enbo Street 1028, Fuyang,Hangzhou ,ZheJiang
Contact name:Yvonne Han
Hangzhou Powersonic Equipment Co., Ltd. |
|
Verified Suppliers
|
|
|
Products Details
| type | Rinco |
| frequency | 20KHz |
| Model | Depending on your requirements |
| power supply | AC220v |
| Maiterial | Titaniu, alloy |
What's ultrasonic booster?
There are three types of ultrasonic boosters with different
mounting systems:
1) standard mount; 2) rigid mount with square O-rings and removable
clamp rings (which also is repairable); and 3) solid mount that
provide improved rigidity. For continuous applications, solid mount
ultrasonic boosters deliver more energy to the product, while in
plunge applications, improved alignment is possible. For more
information on solid mount boost.
According to the type of vibration, it can be divided into
longitudinal vibration, torsional vibration, bending vibration and
composite vibration (longitudinal bending, longitudinal torsion,
bending torsion). In the processing and processing applications of
power ultrasound, longitudinal vibration applications are most
common.
It is classified from the shape of the bus of a single booster, and it can be divided into ladder, index, catenary, cone, Gauss,
Fourier, cosine and other types. Compound horn.
According to its function, it can be divided into two types of
half-wavelength and quarter-wavelength. Although there are many
classifications, the design of longitudinal, torsional, and
flexural booster starts from their corresponding vibration equations, and the design
process and steps are the same.
On the ultrasonic transducer / ultrasonic booster / ultrasonic horn should use o-ring ultrasonic boosters, as they absorb some of the side loads which would otherwise lead to premature failure of the ultrasonic horn in the stud area.
Stud Sizes:
Aluminum 15 – 20 – 25 kHz ultrasonic boosters with ratios of 1:0.6, 1:1, 1:1.5, and 1:2 are available with the ultrasonic horn end drilled and tapped either 1/2-20 or 3/8- 24. Titanium 15khz, 20khz 25 kHz boosters in all ratios, including 1:2.5, are available with 1/2-20 or 3/8-24 tap. ultrasonic Boosters for 28Khz 30khz 35khz, 36khz 40 kHz are available with the ultrasonic horn end drilled and tapped for M-8 threads.
Ultrasonic Boosters are available with ratios of 1:0.5, 1:1, 1:1.5, 1:2, 1:2.5 and 1:3.0
The material of ultrasonic welding booster:
As an important part of ultrasonic welding system, ultrasonic booster are mainly used for energy transfer and amplification in ultrasonic welding. The energy transmitted to the welding surface and the strength of the weld obtained by welding have a direct impact. The efficiency of the horn's energy transfer depends not only on the design of the booster, but also on its material. Aiming at the ultrasonic boosters of different materials, such as aluminum alloy, low carbon steel, stainless steel and titanium alloy, the relationship between the material of the booster and the ultrasonic welding strength was analyzed by using a single factor analysis method. The experimental results show that the strength of the weld obtained by the titanium alloy booster is the highest, followed by low carbon steel, aluminum alloy and stainless steel.
How to design the half-wavelength ultrasonic booster:
1. Traditional analytical method
2. Equivalent circuit method
3. Alternative method (mechanical impedance equalization method)
4. Transfer Matrix Method
5. finite element method(FEA)
6. Other methods: Luffing rod design methods include transmission
line method, piecewise approach method, apparent elasticity method,
etc.
