Active Member
|
[China]
Address: 18F, Building 2, Nantai Yunchuanggu, Phoenix Community, Guangming District, Shenzhen, Guangdong, China
Contact name:Amy
Shenzhen FRIDA LCD Co., Ltd |
|
|
10.1 Inch 1280x800 Ips Lcd Display 40 Pins Lvds BP101WX1-206 330
Nits
General Description:
The manufacturer of BP101WX1-206 is BOE, the product model is
BP101WX1-206, the screen size is 10.1", the resolution is 1280×800,
the resolution is WXGA for short, the display ratio is 16:10, and
the pixel arrangement is RGB vertical strips.
Features:
Specifications:
| Parameter | Specification | Unit | Remarks |
| Active area | 216.96(H) × 135.60(V) | mm | |
| Number of pixels | 1280(H) × 800(V) | pixels | |
| Pixel pitch | 169.5 | ㎛ | |
| Pixel arrangement | Pixels RGB stripe arrangement | ||
| Display colors | 16.7M(6bits + Hi-FRC) | colors | |
| Display mode | Transmission mode. Normally Black | ||
| Outline Dimension | 228.6 × 149.2 × 2.39typ. | mm | |
| Weight | 150 (max) | gram | |
| Surface Treatment | Hard Coating, 3H, Low Reflection (Front Polarizer) | ||
| Back-light | Bottom edge side, 1-LED Lighting Bar Type | 36* LED Array |
| Parameter | Symbol | Min. | Max. | Unit | Remarks |
| Power Supply Voltage (LCD Module) | VDD | -0.3 | 4.2 | V | |
| Back-light Power Supply Voltage | HVDDOUT | -0.3 | 18 | V | |
| Back-light LED Current | IHVDD | - | 96 | mA | |
| Back-light LED Reverse Voltage | VR | - | 2 | V | |
| Operating Temperature | TOP | 0 | +50 | C |
|
| Storage Temperature | TST | -20 | +60 | C |
Electrical Specifications:
Parameter | Symbol | Values | Unit | Notes | ||
| Min | Typ. | Max | ||||
| Power Supply Input Voltage | VDD | 3.0 | 3.3 | 3.6 | V | Note 1 |
| Power Supply Current | IDD | - | 303 | - | mA | |
| LED Driver Power Supply Voltage | HVDD | 3 | - | 18 | V | |
| LED Driver Power Supply Current | IHVDD | - | 568 | - | mA | |
| LED Driver Efficiency | η | - | 85 | - | % | |
| Positive-going Input Threshold Voltage | VIT+ | - | - | +100 | mV | Vcom = 1.2V typ. |
| Negative-going Input Threshold Voltage | VIT- | -100 | - | - | mV | |
| Differential input common mode voltage | Vcom | - | 1.2 | - | V | VIH=100mV, VIL=-100mV |
Power Consumption | PD | - | 1.0 | W | ||
PBL | - | 2.4 | W | Have Driver | ||
PTotal | - | 3.4 | W | |||
Notes: 1.The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for 3.7V at 25C Max value at White Pattern. 2.Calculated value for reference(VLED X ILED) 3.CTF of Power Supply Current:PD/PBL.
Optical Specification:
| Parameter | Symbol | Condition | Min. | Typ. | Max. | Unit | Remark | |
| Viewing Angle range | Horizontal | Θ3 | CR > 10 | 70 | 80 | - | Deg. | Note 1 |
| Θ9 | 70 | 80 | - | Deg. | ||||
| Vertical | Θ12 | 70 | 80 | - | Deg. | |||
| Θ6 | 70 | 80 | - | Deg. | ||||
| Color Gamut | - | 50 | - | % | ||||
| Luminance Contrast ratio | CR | Θ = 0. | 600 | - | - | Note 2 | ||
| Luminance of White | 5 Points | Y |
Θ = 0. | 280 | 330 | - | cd/m2 | Note 3 |
White Luminance uniformity | 5 Points | ΔY5 | - | 80 | - | Note 4 | ||
| White Chromaticity | Wx | Θ = 0. | Typ. -0.03 | 0.313 | Typ. +0.03 | Note 5 | ||
| Wy | 0.329 | |||||||
| Reproduction of color | Red | Rx | Θ = 0. |
Typ. -0.03 | 0.600 |
Typ. +0.03 | ||
| R | 0.340 | |||||||
| Green | Gx | 0.315 | ||||||
| G | 0.565 | |||||||
| Blue | Bx | 0.150 | ||||||
| By | ||||||||
| 0.125 | ||||||||
| Response Time (Rising + Falling) | TRT | Ta= 25.C Θ = 0. | - | 25 | - | ms | ||
| Cross Talk | CT | Θ = 0. | - | - | 2.0 | % | ||
Notes :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface.
2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state . Luminance Contrast Ratio (CR) is defined mathematically.
3. Center Luminance of white is defined as luminance values of 5point average across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations for a total of the measurements per display, the LED current is set at 20mA.
4. The White luminance uniformity on LCD surface is then expressed as : ΔY = Minimum Luminance of 5 (13)points / Maximum Luminance of 5(13).
5. The color chromaticity coordinates specified in Table 5 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.
Interface Connection:
The electronics interface connector is 20455-040E-12.
| Terminal | Symbol | Functions |
| Pin No. | Symbol | Description |
| 1 | NC | Non Connection |
| 2 | VDDIN | Power supply VDDIN=3.3V (Typ.) |
| 3 | VDDIN | |
| 4 | VDC | Power supply VDC=3.3V (Typ.) |
| 5 | NC | Non Connection |
| 6 | CLK EDID | CLK for EDID function use |
| 7 | Data EDID | CLK for EDID function use |
| 8 | RIN0- | LVDS Negative data signal (-) |
| 9 | RIN0+ | LVDS Positive data signal (+) |
| 10 | GND | GROUND |
| 11 | RIN1- | LVDS Negative data signal (-) |
| 12 | RIN1+ | LVDS Positive data signal (+) |
| 13 | GND | GROUND |
| 14 | RIN2- | LVDS Negative data signal (-) |
| 15 | RIN2+ | LVDS Positive data signal (+) |
| 16 | GND | GROUND |
| 17 | LVDS_CLK- | LVDS Negative CLK signal (-) |
| 18 | LVDS_CLK+ | LVDS Positive CLK signal (+) |
| 19 | GND | GROUND |
| 20 | RIN3- | LVDS Negative data signal (-) |
| 21 | RIN3+ | LVDS Positive data signal (+) |
| 22 | CE_EN | Color engine enable |
| 23 | NC | Non Connection |
| 24 | NC | Non Connection |
| 25 | GND | GROUND |
| 26 | NC | Non Connection |
| 27 | NC | Non Connection |
| 28 | GND | GROUND |
| 29 | NC | Non Connection |
| 30 | NC | Non Connection |
| 31 | LED_GND | LED GROUND |
| 32 | LED_GND | |
| 33 | LED_GND | |
| 34 | NC | Non Connection |
| 35 | LED_PWM | LED driver PWM duty |
| 36 | LED_EN | LED driver enable |
| 37 | CABC_EN | CABC function enable |
| 38 | VLED | Power supply VLED=3~18V (Typ.) |
| 39 | VLED | |
| 40 | VLED |
Dimensional Requirements:
| Parameter | Specification | Unit |
| Active Area | 216.96 (H) × 135.6 (V) | |
| Number of pixels | 1280(H) X800 (V) (1 pixel = R + G + B dots) | |
| Pixel pitch | 0.1695 | |
| Pixel arrangement | RGB Vertical stripe | |
| Display colors | 16.7M | |
| Display mode | Normally Black | |
| Dimensional outline | 228.6*149.26*2.39 (Typ.) | mm |
| Weight: | 150 (Max) | gram |
| Back-light | LED, Horizontal-LED Array type |
Matters Needing Attention:
Cautions when taking out the module:Pick the pouch only, when taking out module from a shipping package.
Cautions for the operation:When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged.
Other cautions:Do not disassemble and/or re-assemble LCD module.Do not re-adjust variable resistor or switch etc.When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages.
Reliability Test:
| No | Conditions | |
| 1 | High temperature storage test | Ta = 60 C, 240 hrs |
| 2 | Low temperature storage test | Ta = -20 C, 240 hrs |
| 3 | High temperature & high humidity operation test | Ta = 50 C, 90%RH, 240 hrs |
| 4 | High temperature operation test | Ta = 50 C, 240 hrs |
| 5 | Low temperature operation test | Ta = 0 C, 240 hrs |
| 6 | Thermal shock | Ta = -20 C ↔ 60 C (0.5 hr), 100 cycle |
| 7 | Power on/off | 2s on/2s off 20000cycles |
| 8 | Vibration test (non-operating) | 1.5G, 10~500Hz Sign X,Y,Z / Sweep rate : 0.5hour |
| 9 | Shock test (non-operating) | 220G, Half Sine Wave 2msec ± X,±Y,± Z Once for each direction |
| 10 | Electro-static discharge test (non-operating) | Air : 150 pF, 330Ω, 15 KV Contact : 150 pF, 330Ω, 8 KV |
