Home Companies Jiaxing City Qunbang Hardware Co., Ltd

A354 ANSI Carbon Steel HDG Fully Threaded Studs

Contact Us

[China]

Trade Verify

Address: No.375,Tongle Road,Jiaxing City,Zhejiang Province,China

Contact name:Lance

Jiaxing City Qunbang Hardware Co., Ltd

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

A354 ANSI Carbon Steel HDG Fully Threaded Studs

Country/Region	china
City & Province	jiaxing zhejiang
Categories	Bolts

Product Details

A354 ANSI Carbon Steel HDG 1 Inch All Thread Rod

ASTM A354 covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4” and under in diameter. Two strength levels, grades BC and BD are summarized below. This specification is unrestricted in its configuration and can be a headed bolt, bent bolt, or threaded rod.

Screw Thread
d

d
PP	UNC
	UNF
	8UN
u	max	UNC
		UNF
		8UN

0.2500	0.3125	0.3750	0.4375	0.5000	0.5625	0.6250	0.7500	0.8750	1.0000	1.1250	1.2500	1.3750
20	18	16	14	13	12	11	10	9	8	7	7	6
28	24	24	20	20	18	18	16	14	12	12	12	12
-	-	-	-	-	-	-	-	-	-	8	8	8
0.100	0.111	0.125	0.143	0.154	0.167	0.182	0.200	0.222	0.250	0.286	0.286	0.333
0.071	0.083	0.083	0.100	0.100	0.111	0.111	0.125	0.143	0.167	0.167	0.167	0.167
-	-	-	-	-	-	-	-	-	-	0.250	0.250	0.250

Screw Thread
d

d
PP	UNC
	UNF
	8UN
u	max	UNC
		UNF
		8UN

1.5000	1.6250	1.7500	1.8750	2.0000	2.2500	2.5000	2.7500	3.0000	3.2500	3.5000	3.7500	4.0000
6	-	5	-	4-1/2	4-1/2	4	4	4	4	4	4	4
12	-	-	-	-	-	-	-	-	-	-	-	-
8	8	8	8	8	8	8	8	8	8	8	8	8
0.333	-	0.400	-	0.444	0.444	0.500	0.500	0.500	0.500	0.500	0.500	0.500
0.167	-	-	-	-	-	-	-	-	-	-	-	-
0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250	0.250

A354 Grades

BD	Grade BD bolts are higher in strength than grade BC, and equal in strength to ASTM F3125 grade A490 bolts. Unlike A490 however, the A354 standard is unrestricted in its configuration. Also, since A490 bolts are for structural use and do not exceed 1-1/2” in diameter, A354 grade BD should be considered for anchor bolts, threaded rods, other styles of headed bolts, and bolts larger than 1-1/2” diameter where similar mechanical properties are desired. A354 grade BD does not require a magnetic particle test like A490, except when called out as a supplemental requirement.
BC	Lower in strength than BD. Should be considered in lieu of F3125 grade A325 bolts when configuration and size conflicts occur with A325 as described above for grade BD and A490 bolts./td>

Grade BD bolts are higher in strength than grade BC, and equal in strength to ASTM F3125 grade A490 bolts. Unlike A490 however, the A354 standard is unrestricted in its configuration. Also, since A490 bolts are for structural use and do not exceed 1-1/2” in diameter, A354 grade BD should be considered for anchor bolts, threaded rods, other styles of headed bolts, and bolts larger than 1-1/2” diameter where similar mechanical properties are desired. A354 grade BD does not require a magnetic particle test like A490, except when called out as a supplemental requirement.

Lower in strength than BD. Should be considered in lieu of F3125 grade A325 bolts when configuration and size conflicts occur with A325 as described above for grade BD and A490 bolts./td>

A354 Mechanical Properties

Grade	Size	Tensile, ksi, min	Yield, ksi, min	Elong %, min	RA %, min	Hardness, HRC
BC	1/4 - 2-1/2	125 min	109	16	50	26 - 36
BC	Over 2-1/2	115 min	99	16	45	22 - 33
BD	All Sizes	150 - 173	130	14	40	33 - 38

A354 Chemical Properties

Element	All sizes of Grade BC, Grade BD through 2-1/4” diameter.	Grade BD over 2-1/4”
Carbon, %	0.30 to 0.53	0.35 to 0.53
Manganese, % min	0.60	0.60
Phosphorus, % max	0.035	0.035
Sulfur, % max	0.040	0.040
Boron, % max	0.003	0.003
Nickel, % min		0.40
Chromium, % min		0.40
Molybdenum, % min		0.15
Other Alloying Elements	*	*
*steel is considered to be alloy when the maximum range given for manganese exceeds 1.65 % or a definite minimum quantity for any of the following elements is specified or required within the limits of the recognized field of constructional alloy steels: chromium, molybdenum, nickel, or any other alloying element added to obtain a desired alloying effect.

Additional Requirements, Grade BD, Diameters above 2-1/4”

Charpy Impact	20ft-lbs minimum @ -4F
Cross Sectional Hardness	Equidistant hardness readings shall be taken across the diameter of the fastener through the threaded section. Reading shall be no further apart than ¼”. No reading shall be outside the acceptable range given above, and no reading shall be greater than +/- 3 HRC points from the average mid-radius hardness value.

A354 Recommended Hardware

Grade	Finish	Nut	Washer
BC	Plain	A563C Heavy Hex	F436
BC	Galvanized	A563DH Heavy Hex	F436
BD	All Finished	A563DH Heavy Hex	F436
* Nuts of other grades and styles having specified proof load stresses greater than the specified grade and style of nut are acceptable.

Specification

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

All thread rod, commonly referred to as fully threaded rod, redi-rod, continuously threaded rod, TFL rod, and abbreviated ATR is used for general purpose fastening for anything from an anchor bolt to a through bolt. A variety of grades and materials are available.

Materials and Chemical compstition

1008

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	Ni	Cu	Al
0.06	0.06	0.33	0.013	0.003	0.01	0	0.01	0.028

1035

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	Ni	Cu
0.34	0.13	0.73	0.012	0.002	0.02	0.01	0.02

10B21

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	B
0.2	0.04	0.81	0.017	0.007	0.017	0.0021

1045

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	Ni	Cu
0.45	0.23	0.58	0.014	0.006	0.057	0.008	0.016

40CR

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	Ni	Cu
0.4	0.21	0.54	0.015	0.008	0.95	0.02	0.02

35CRMO

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	Ni	Cu	Mo
0.35	0.22	0.59	0.01	0.003	0.93	0.01	0.01	0.21

42CRMO

CHEMICAL COMPOSI %
C	Si	Mn	P	S	Cr	Ni	Cu	Mo
0.42	0.27	0.92	0.013	0.004	1.01	0.03	0.04	0.2

Finish

PLAIN ZP YZP BLACK HDG DACROMET GEOMET CHROME NICKEL AND SO ON

PACKING

QBH BULK

20-25KG/CTN,36CTNS/PALLET

20-30KG/BAGS,36BAGS/PALLET

ONE TON/BOXES

50KG/ IRON DRUM,12 IRON DRUMS/PALLET

QBH SMALL PACKING

Packing in small boxes according to customer’s requirements

Packing in plastic bag according to customer’s requirements

QBH PALLET TYPE

SOLID WOOD FUMIGATION PALLET

EURO Pallet

THREE SPLINT PALLET

WOODEN BOX

The advantages of QBH

QBH brand sales to the main quality assurance.
Years of export trade management, excellent service, word-of-mouth guarantee.
By working with TUV,escort for quality.
Customization of non-standard parts can be made according to customer's requirements and drawings.
For quality customers,we can provide a certain credit period.