|
[China]
Trade Verify
Address: 4/F, Block C, HeHengXing Science & Technology Park, 19 MinQing Road, LongHua District, Shenzhen City, GuangDong Province, China
Contact name:Sun
Shenzhen Socay Electronics Co., Ltd. |
|
Verified Suppliers
|
|
|
Original Factory SOCAY Resettable Polymer PPTC SC250-600CZ0D In Stock
Resettable Polymer PPTC DATASHEET: SC250-600CZ0D_v98.1.pdf
Electrical Parameters:
| Part Number | I hold (A) | I trip (A) | V max (Vdc) | I max (A) | Pdtyp (W) | Maximum Time To Trip | Resistance | |||
| Resettable Polymer PPTC | Current (A) | Time (S) | R min (Ω) | R max (Ω) | R1max (Ω) | |||||
SC250-600CZ0D | 0.60 | 1.20 | 220 | 3.0 | 4.0 | 3.0 | 10.0 | 0.50 | 0.75 | 1.13 |
About PPTCs
PTC (Polymer Positive Temperature Coefficient) devices can help protect against overcurrent surges and overtemperature failures. Thermistor-type devices limit the flow of dangerously large currents during fault conditions. However, it is different from traditional fuses that can only be used once and must be replaced. The PTC device that Jidentong has carefully crafted over many years can be reset after troubleshooting and disconnecting the power supply, thereby reducing component costs and service fees. PTC circuit protection devices are made of polymer PTC raw materials mixed with nano conductor particles. At normal temperatures, the material tightly binds the conductor into a crystalline structure, forming a low-impedance link. However, when a large current passes through or the ambient temperature rises, causing the device temperature to be higher than the operating temperature, the conductors in the polymer melt and become irregularly arranged, causing the volume to expand and cause the impedance to increase rapidly.
Typical applications of resettable fuses in electronic circuits:
1. Protection of battery charger
In the battery charger circuit, the unregulated DC output voltage
of the power converter is modulated by the voltage stabilizing
circuit and converted into an appropriate voltage to charge the
battery. PPTC devices and voltage overload protection devices
cooperate with each other to protect against the following faults:
*Excessive current. Excessive current may damage the power FET or
battery pack;
*Reverse polarity. At this time, the diode is turned on and the
PPTC device enters a high impedance state to limit the current;
*The voltage is too high. At this time, the voltage overload
protection device works, and the PPTC device limits the current.
Resettable Polymer PPTC Features:
u RoHS Compliant and Halogen-Free u Radial leaded Devices u Cured,flame retardant epoxy polymer insulating material meets UL94V-0 requirements u PPTC Resettable Fuse Operation Current: 0.90A, Maximum Voltage: 60Vdc, Operating Temperature: -40℃ to +85℃ |
Resettable Polymer PPTC Applications:
u USB hubs, ports and peripherals u Power ports u IEEE1394 ports u Motor protection u Computers and peripherals u General electronics |
Temperature Rerating Chart – I hold (A):
| Ambient Operation Temperature | -40℃ | -20℃ | 0℃ | 23℃ | 30℃ | 40℃ | 50℃ | 60℃ | 70℃ | 85℃ |
| Percentage Reduction | 145% | 130% | 120% | 100% | 95% | 88% | 80% | 71% | 66% | 56% |
Test Procedures and Requirement:
| Test | Test Conditions | Accept/Reject Criteria |
| Resistance | In still air @25±2°C | Rmin≤R≤Rmax |
| Hold Current | 60 min, at Ihold, In still air @25±2°C | No trip |
| Time to Trip | Specified current, Vmax, @25±2°C | T≤Maximum Time To Trip |
| Trip Cycle Life | Vmax, Imax,100 cycles | No arcing or burning |
| Trip Endurance | Vmax,24hours | No arcing or burning |
Resettable Polymer PPTC Physical Specifications:
| Lead Material | 0.03-1.85A Tin-plated Copper clad steel 2.50-5.00A Tin-plated Copper |
| Soldering Characteristics | Solder ability per MIL-STD-202, Method 208E |
| Insulating Material | Cured, flame retardant epoxy polymer meets UL 94V-0 requirements. |
| Device Labeling | Marked with ‘SC’, voltage, current rating |
Resettable Polymer PPTC Packaging Quantity:
| Part Number | Quantity (pcs/reel) |
SC250-600CZ0D | 500 |
FAQ
Q1. Can I have a sample order ?
A: Yes, we welcome sample order to test and check quality. Mixed
samples are acceptable.
Q2. What about the lead time?
A:Sample needs 1 days, mass production time needs 1-2 weeks for
order quantity more than
Q3. Do you have any MOQ ?
A: MOQ depend on the type of product, 1pc for sample checking is
available
Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5
days to arrive. Airline and sea shipping also optional.
Q5. How to proceed an order ?
A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our
suggestions.
Thirdly customer confirms the samples and places deposit for formal
order.
Fourthly We arrange the production.
