Active Member
|
[China]
Address: Fuyong Xinhe Sanqu, 7 Xiang 12 Hao 102, Bao'an, Shenzhen, Guangdong, China
Contact name:Su Zhongqiu
Shenzhen Wanbo Hi-Tech Co., Ltd. |
|
|
Element Height 6mm Used SMT Equipment With 6 Standard SMD Heads
JUKI KE-2070 equipped with 6 standard SMD heads Element height 6mm specifications
JUKI KE-2070 Pick And Place Machine Remote technical support of equipment
Multifunctional SMT Placement Machine 6 Heads For LED Power Driver / IC Chip
Shenzhen Wanbo High-tech Co., Ltd. has a JUKI senior engineer team with rich maintenance experience, specializing in providing JUKI series placement machine software and hardware maintenance and troubleshooting. It mainly includes JUKI laser head, CPU motherboard SUB-CPU board, drive board X/Y/Z/T axis driver, head board, image control card, I/O board, JUKI servo motor, camera, display touch screen, servo motor and other maintenance and replacement services. The company's fees are reasonable, the warehouse accessories are sufficient, the maintenance cycle is short, the one-time repair success rate is high, and the Pearl River Delta region can provide door-to-door installation, commissioning, maintenance and maintenance.
Overview of operations
Step 1Turn on the power of the main unit.
Check to see if there is no substance such as a board or tool
inside the machine.Rotate the main switch to the right to check the
air meter (pressure gauge).
Turn the main switch to the rightby 90 degrees.
Power: OFF>
Power: ON
Check the air meter
(pressure gauge).<Proper pressure>0.5Mpa+0.05
*lf the pressure is less than 0.4
Mpa, check the air system.
3After Windows XP and the main unit software start up in this
order, the message
appears on the screen.
wWhen you select <OK>, the axes of the machine start retuning
to their respectivehome positions.
Select <OK>.
All axes move,and start returningto their home positions.
WARNING
When you return the axes to their home positions (by pressing
<OK>on the screen above), the machine starts operating. To
avoid riskof injury, never put your hand or head inside the
machine.
Only after you check to see if there is no substance such as
awrench that may be in contact with the head inside the
machine,return the axes to the home positions.
| Model name | High speed placement machine KE-2070M/L/E |
| Substrate size | M substrate (330×250mm) ○ l For substrate (410×360mm) ○ E substrate (510×460mm) ○ |
| Element height | 6mm specifications ○ 12mm specifications ○ 20mm Specifications _ 25mm Specifications _ |
| Component size | Laser identification 0402 (imperial 01005) chip ~ 33.5mm square element Image recognition 1.0×0.5mm~33.5mm square element |
| Component placement speed | Optimal conditions 0.155 sec/chip (23300CPH) IC Component 4600CPH* |
| Component placement accuracy | Laser recognition ±0.05mm Image recognition ±0.04mm |
| Component placement type | Up to 80 types (converted to 8mm belt) |
| power supply | Three-phase AC200~415V |
| Rated power | 3KVA |
| Use air pressure | 0.5±0.05Mpa |
| Air consumption | (Standard status) 345L/min |
| Device size (W×D×H) | M substrate 1,400×1,393×1,455mm L substrate 1,500×1,500×1,455mm E substrate 1,730×1,600×1,455mm |
| weight | 1530kg |
Accessories include: all kinds of original, domestic nozzles, FEEDER, boards, lasers, solenoid valves, inductors,
cylinders, tank chains, etc.), laser maintenance, board maintenance and so on.
