Active Member
|
[China]
Address: Fuyong Xinhe Sanqu, 7 Xiang 12 Hao 102, Bao'an, Shenzhen, Guangdong, China
Contact name:Su Zhongqiu
Shenzhen Wanbo Hi-Tech Co., Ltd. |
|
|
Used JUKI 6 Heads SMT Placement Machine For LED Power Driver IC Chip
Multifunctional SMT Placement Machine 6 Heads For LED Power Driver / IC Chip
Juki KE-2070L SMT Machine Suitable for high-speed placement of small components
Used Juki KE-2070 smd equipment 23300CPH laser identification/condition
6 suction nozzles JUKI2070 SMT Assembly Machine Fast Speed For 1.2m PCB LED Strip
Used Juki KE-2070 Smd assembly machine Paste Bridge pile Convex lens on PCB
Shenzhen Wanbo High-tech Co., Ltd. has a JUKI senior engineer team with rich maintenance experience, specializing in providing JUKI series placement machine software and hardware maintenance and troubleshooting. It mainly includes JUKI laser head, CPU motherboard SUB-CPU board, drive board X/Y/Z/T axis driver, head board, image control card, I/O board, JUKI servo motor, camera, display touch screen, servo motor and other maintenance and replacement services. The company's fees are reasonable, the warehouse accessories are sufficient, the maintenance cycle is short, the one-time repair success rate is high, and the Pearl River Delta region can provide door-to-door installation, commissioning, maintenance and maintenance.
Keyboard:
Switches the side on which the switches can be
operated,<FRONT> or之REAR>.
(when the optional rear operation unit is used)
Feeder:Switches whether a feeder unit is enabled or disabled.(when
the optional non-stop operation function is used)
Online:Use to allow the machine to connect to the lS or the HLC (enter the online status).The switch lights up when the machine enters Online mode.
Start:This is the switch for start.Use to start an actual production run.use to free the servo motor (X-axis, Y-axis,Z-axis, and q-axis).
servo free
The switch lights up when servo motor is set into the free state.
The motor is energized again when the switch is pressed the second
time.
Origin:Use to zero all the axes.
PauselStop:
Use this switch to terminate PWB production or another operation.
Press the switch once to put the production run in a pause status.
Press theswitch the second time to stop the production run.
Single cycle:
use to stop the production run when one board has been produced.
Press the switch a second time to exit from this status.
Emergency
This is the switch for emergency stop.
Use this switch to immediately stop the machine when it
malfunctions or whenit may pose risks to your safety.When you turn
it in the direction indicated
with the arrow mark, the machine is recovered from this emergency
stop state.
| Model name | High speed placement machine KE-2070M/L/E |
| Substrate size | M substrate (330×250mm) ○ l For substrate (410×360mm) ○ E substrate (510×460mm) ○ |
| Element height | 6mm specifications ○ 12mm specifications ○ 20mm Specifications _ 25mm Specifications _ |
| Component size | Laser identification 0402 (imperial 01005) chip ~ 33.5mm square element Image recognition 1.0×0.5mm~33.5mm square element |
| Component placement speed | Optimal conditions 0.155 sec/chip (23300CPH) IC Component 4600CPH* |
| Component placement accuracy | Laser recognition ±0.05mm Image recognition ±0.04mm |
| Component placement type | Up to 80 types (converted to 8mm belt) |
| power supply | Three-phase AC200~415V |
| Rated power | 3KVA |
| Use air pressure | 0.5±0.05Mpa |
| Air consumption | (Standard status) 345L/min |
| Device size (W×D×H) | M substrate 1,400×1,393×1,455mm L substrate 1,500×1,500×1,455mm E substrate 1,730×1,600×1,455mm |
| weight | 1530kg |
Accessories include: all kinds of original, domestic nozzles, FEEDER, boards, lasers, solenoid valves, inductors,
cylinders, tank chains, etc.), laser maintenance, board maintenance and so on.
