|
[China]
Trade Verify
Address: Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China
Contact name:Zoe Zou
Sinuo Testing Equipment Co. , Limited |
|
Verified Suppliers
|
|
|
IEC 62133-1 Battery Vibration Impact Test Bench With Real-Time Display Function
Overview:
This vibration system conforms to IEC 60068-2-6, it is required by IEC 62133-1:2017 clause 7.2.2, IEC 62133-2:2017 clause 7.3.8.1,etc.
Technical Parameters:
| Vibration generator | |
| Sinusoidal thrust | 2940N (300kg.f) |
| Random thrust | 2940N (300kg.f) |
| Impact thrust | 5880N(600kg.f) |
| Frequency range | DG～3500Hz |
| Continuous displacement | 20mm |
| Impact displacement (maximum displacement) | 25mm |
| Maximum speed | 1.8m/s |
| Maximum acceleration | 981m/s2 (100g) (No-load) |
| Dynamic diameter | Φ150mm |
| First-order resonant frequency | 2900 Hz±5% |
| Allowable eccentric moment | ≤2500N·cm |
| Equivalent mass of moving parts | 3kg |
| Load connection point | 13 |
| Table screw size (standard) | M8 |
| Table screw layout (diameter, Yuan Zhou) | 13-M8 Depth 16mm |
| Axial vibration isolation frequency | ＜3Hz |
| Maximum load | 120kg |
| Magnetic flux leakage | ≤1mT |
| Ambient temperature | 0~40℃ |
| Size | 1600mm×800mm×700mm |
| Weight | 1100kg |
| Power amplifier output | 3kVA |
| Signal-to-noise ratio | ＞65dB |
| System protection |
|
| Rated output voltage | 100Vrms |
| Output current | With the 150A step, the maximum can be up to 6000A |
| Input impedance | ≥15kΩ |
| Input signal voltage | ≤1.5Rms |
| Efficiency of power amplifier | ＞92% |
| Harmonic distortion (resistance load) | ＜1.0% |
| Output voltage measurement error | ≤5% |
| Output current measurement error | ≤5% |
| Output current crest factor | ≥3 |
| DC stability | Zero drift at the output is less than 30mv/8h |
| Frequency range | 1-3500Hz:±3dB ； Medium frequency gain:≥80 |
| DC/AC conversion efficiency | ＞92% |
| Load property | Resistive, capacitive, emotionally arbitrary |
| Unbalance of parallel flow | ≤2.8% |
| Average time free working time(MTBF) | ＞3500 hours |
| Cooling mode | Forced air cooling |
| Power | AC 3phase 380V±10%, 60Hz |
| Size | 600mm×620mm×1600mm |
| Weight | 580kg |
| Cooling fan with muffler | |
| Fan power | 0.75kW |
| Air volume | 0.1m3/s |
| Duct diameter | 125mm |
| Duct length | 4m |
| wind pressure | 1kpa |
| Size | 500mm×520mm×650mm |
| Weight | 30kg |
| Horizontal extension slide | |
| Platform size | 500×500mm |
| Equivalent mass (maximum load-bearing) | 28kg |
| Upper bound frequency | Sine 2000Hz, random 2000HZ |
| Material | Magnesium aluminum alloy |
| Vertical Expansion Table | |
| Platform size | 500mm×500mm |
| Equivalent mass (maximum load-bearing) | 28kg |
| Upper bound frequency | Sine 1500Hz,random 2000HZ |
| Material | Magnesium aluminum alloy |
1．Sinusoidal Control Measurement System Specifications and Functions:
| Frequency range | 2-5000Hz |
| Crossing point | 32 segments, and can wait for displacement, equal speed, etc. |
| Frequency display | The vibration test curve set by the man-machine dialogue can be directly displayed on the screen. In the vibration test, the vibration curve can be displayed in real time, and the error dB at the time can be displayed continuously. |
| Output voltage | 7Vrms |
| Sweep mode | Linear, logarithmic |
| Sweep rate | 0.1-10oct/min |
| Control accuracy | ±0.5dB |
| Dynamic Range | 79dB |
| Control method | Peak, average, rms, tracking filter |
| Vibration Mode | Constant Frequency, Sweep (Linear, Logarithmic), Pause, Resume, Return |
| Filter form | Biased anti-aliasing filter (eight-stage) passband 0.2dB/oct |
| Signal form | Sine wave |
| Waveform distortion | ≤0.5% |
Setup function: The test specification of the human-machine dialogue setup can be saved for reuse The controller can be on the rack, integrated with the amplifier cabinet, and can also be separated from the amplifier cabinet | |
2. Random Control Measurement System Specifications and Functions:
| Frequency range | 100,200,400,500,1000,2000,4000,5000Hz |
| Resolution | 100,200,400,800 lines |
| Driving spectrum dynamic range | 60dB |
| Control spectrum dynamic range | 40dB |
| Loop time | 2000Hz, 400 lines single channel 0.6 seconds |
| Power spectrum control accuracy | ±1dB (90% confidence) |
| RMS value control accuracy | ±0.2dB |
| Control Channels | Independent Channels |
| Control method | Average, maximum |
| Spectral settings | Up to 32 levels, both with PSD [(m.s2)2/Hz] and dB/oct settings |
3.Impact control measurement system technology standard and function:
| Waveform | Half Sine, Triangle, Sawtooth, Square Wave |
| Frequency Range | 5-2000Hz |
| Vibration level presets | -18dB, -15dB, -12dB,-9dB,-6dB,-3dB,0dB seven vibration levels, vibration time for each vibration level :Set by the user. |
| Upgrade Modes | Automatic upgrade and manual upgrade |
| Display function | With real-time display, print function. |
| Protection function | Over-limit alarm, open-circuit protection and automatic over-limit shutdown |
| Setting function | The test specification set during the man-machine conversation can be saved for repeated use. |
| Measuring range | 0-200g divided into eight gears 1,2.5,5,10,25,50,100,200g range automatically shift |
| Filter Format | Programmable anti-aliasing filter (eight-stage) 0.2dB pass band and -55dB/oct stop band |
| Signal form | True random, pseudo-random |
4. Characteristics and Technical Specifications of USB01 Card:
| Full-scale input | 16-bit 16-channel single-ended A/D, speed 400KS/S, +/-5V |
| Full-scale output | One 16-bit D/A, +/-5V |
| Win-XP | Supports USB1.1 and USB2.0 standards for Win-2000 |
| Main Controller | 32-bit 120MHz Floating Point Digital Signal Processor (DSP) |
| Digital output | 8 bits |
| High-speed continuous acquisition | 34K*32Bit high-speed static memory |
| Clock signal output | 819.2K filter |
| Input Channel | 16-channel single-ended |
| Analog Input Signal Voltage Range | Bipolar +/-5V |
| Resolution | 16 bits |
| A/D conversion time | 2.5 microseconds |
| Acquisition pass rate | 400KHz |
| Accuracy | Better than 0.015% |
| Nonlinear deviation | <4 LSB |
| Data Format | 16-bit twos complement |
| Input impedance | 10 MΩ |
| A/D conversion trigger mode | Instruction, timer |
| D/A output signal voltage range | Bipolar +/-5V |
| D/A resolution | 16 bits |
| Digital/analog conversion time | 5 microseconds |
| Accuracy | better than 0.015% |
| Nonlinear deviation | <4 LSB |
| Data Format | 16-bit twos complement |
| Output impedance | <0.1Ω |
| Main controller | 32-bit 120MHz floating point DSP TMS320VC33 |
| System clock | 40.96KHz |
| Two 32-bit timer/counters | For D/A and A/D timing |
| Digital output | 8 bits(TTL) |
| Clock output | 819.2KHz |
| Power Consumption | <2.5W(5V, 500mA) |
