|
[China]
Trade Verify
Address: No.755, Xianyuehuan Rd, Tianyuan District, Zhuzhou, Hunan Province
Contact name:Shirley
Zhuzhou Ruideer Metallurgy Equipment Manufacturing Co.,Ltd |
|
Verified Suppliers
|
|
|
Return Permeability Ceramic Sintering Furnace / Industrial Vacuum Sintering Furnace
Equipment description:
On the whole, it meets the strict requirements of temperature uniformity and atmosphere uniformity in powder metallurgy.The furnace structure design is advanced and reasonable, which is convenient for operation and maintenance.The main supporting components (sensors, graphite heating element, thermocouple, main control valve, vacuum pump, etc.) have the international advanced level and can adapt to the long-term, stable and reliable mass production requirements.At the same time, the equipment should also meet the national requirements for energy conservation and environmental protection.
Equipment function:
Realize the function of vacuum sintering and rapid cooling;The whole process of manual button operation, temperature control using Yokogawa-550 instrument temperature control.
Working environment of plant:
Humidity and temperature requirement
Environment humidity: ＜90%(at +35℃)
Environment temperature: -10℃～45℃
Power supply
Motive power supply: 375V--430V,50Hz,3 phase 5 wire system;Heating
power:600KVA
Control power supply(China standard): 210V～250V,50Hz,Single-phase
Water:Totally enclosed circulating water
Gas:
Process gas:Ar,N2
Compressed air pressure: 0.6MPa ～0.8MPa
Technical paremeter table
| Design run times | 300 furnace/year |
| Valid working zone size | 500mm×500mm×1500 mm (W×H×L) |
| Max.loading capacity | ≥1000Kg(It depends on the product type) |
| Max.working temperature | 1400℃ |
| Pumping speed | The vacuum degree can reach 5Pa, and then pump within 30min after reaching 5Pa. The ultimate vacuum value should reach 1Pa (in the case of cold, air and dry after heating up furnace). |
| Leakage rate | ≤2Pa/h(after testing the limit vacuum, empty furnace, clean and cold state,average value winthin 12 hours) |
| Max.positive pressure | 10KPa |
| Rapid cooling time≤8h | |
| Max.heating up speed(full loading) | ≥6℃/min |
| Heating power | proximately 220KW |
| Loading plate size | 720*480*35mm(2 plate) |
After sales:
1.Installation, Commissioning And Acceptance
We do installation, commissioning and acceptance in buyer's plant.During the installation and commissioning period, the commissioning personnel shall be provided free of charge by the demander according to the staff standard.
The equipment shipped to the buyer, the seller received the buyer's
notification, both within a week to carry the equipment out of the
box together, then check the equipment and all components according
to the packing list . Including equipment accessories, spare parts
and special tools, attached manual and technical documents, etc. It
can be installed after the acceptance check of equipment.
After installation and debugging, the equipment shall be accepted
according to the technical accessories.
2.Training
When taking-over the Furnace to the customer, We will give a staff
training to customer. The operating personnel of the customer
should join to commission,test the furnace, when installing at
customer’s company.
This is practical operation training and practical maintenance
training,
and our technical personnel will telling the basic
principle,equipment maintenance knowledge,And the common fault
handling measures.We can training 2 ~ 3 workers. ( Training how to
maintenance and operating.)
3. warranty period
The warranty period of the equipment is 12 months, which starts from the date of installation and debugging of the supplier. Equipment failure happens, after-sales service personnel shall give solutions within 2 hours, after receiving the buyer's notification . If it is need to go to the site for treatment , operators dispatched by seller should arrive at the site within 48 hours after go aboard. In case of emergency,operators should arrive at the site within 48 hours after go aboard, and continue to make repairs until the fault is removed and the equipment returns to normal.
