Qingdao Puhua Heavy Industrial Machinery Co., Ltd. |
|
Sand blasting chamber:
This machine is a special reciprocating sand blasting machine,
which consists of shot-peening chamber, shot-peening device, Screw
Conveyor, elevator, separator, Shot distributing system, flat car
system, flat car guide and support, lighting system, the bottom
funnel, grid plate, dust- removing system, electric control system
and so on.
This abrasive material reclaim system requires extremely reduced
foundations, and can optionally be built without the need of
foundations, or still on container type mobile rooms.
Optionally, we can supply room kits with the components that are
necessary for the client, such as, for example, and automatic or
semi-automatic abrasive material reclaim system, exhaust systems,
etc., which will always fully meet the safety and environmental
standards.
1) Doors:
The service door is built in welded profiles and has a closing in
steel plates, and is internally coated with abrasion resistant
rubber. An exclusive sealing system prevents the loss of abrasive
materials and makes the closing of the doors possible, without
effort. Optionally, two doors can be supplied (tunnel type room)
and one door for the operator. Sensors connected to the doors
automatically interrupt the blasting operation when one of them is
opened.
2) Luminaries:
Each LED lamps construction and positioning enable maximum
utilization of the luminosity. The fastening system allows easy
removal, for maintenance.
3) Working chambers:
Built in color steel tile, they are modulated in order to satisfy
any dimension in height, width and length. Inside (except on the
ceiling) there is a rubber coating that protects them against
abrasion and helps in the acoustic insulation.
4) Horizontal transportation of abrasive material:
This system combines the drive of scraper carts that conduct the
abrasive material to the center of the working chamber, where it is
collected by a screw conveyor (in some cases by a belt conveyor)
which conducts the abrasive material up to the foot of the bucket
elevator (abrasive materials purifier). On the whole floor surface,
there is a grid that is covered with a perforated plate, which
retains larger impurities or even small parts which may drop
accidentally on the floor. This unique system used by CMV requires
a much smaller installed power that the other systems, thanks to
the friction coefficient (wear), which is much smaller in this
system.
5) Control panel:
Mounted on a shielded cabinet, it has thermal protection and
interlocking for the motors, which makes it impossible to connect
them in the incorrect order. Optionally, it is supplied with a PLC
for the automatic control of the equipment. It meets the most
important international standards.
6) Blasting machine:
It has a pressure vessel built in accordance with the EU standard,
which is hydrostatically tested to operate at a pressure of 8 Bar
(116PSI), with and outlet for one or more operators, with a remote
pneumatic command and a full kit for the protection of the
operator(s), and an air filter that is appropriate for human
breathing. The machine also has a high-efficiency pneumatic system
and high-performance nozzle(s). Optionally, it can be equipped with
a level sensor for automatic feeding of abrasive material.
7) Abrasive materials purifier / Bucket elevator:
The bucket elevator receives the abrasive in its hopper and lifts
it to the purifier. The elevator features buckets in nodular cast
iron that are highly resistant to abrasion and is driven by one
gear motor. The abrasive materials purifier receives the abrasive
material from the bucket elevator and, with a system that is
adjustable through counterweights, forms a curtain with the
abrasive material, through which an air stream passes, which is
also adjustable, and which takes the dust and other residues that
may be contaminating the abrasive material, to the exhaust system.
The abrasive material, now free from impurities, drops into the
silo that is located on the blasting machine. Optionally, the
abrasive materials purifier can be supplied with a revolving
screen.
Automotive electrostatic car painting equipment/booth Product Detail:
OEM/ODM
We are committed to maintaining our position as the pioneers of our industry.With our own facilities, we can work on your OEM/ODM projects.
Painting room chamber
Each Painting room is tailor made for the specific requirement of each
Customizable trolley system
The trolley load-bearing is 10T.total length of rail is 35 m. To prevent the projectile wheel stuck phenomenon, there are polyurethane scraper in front of each wheel to strike off scattered abrasive on the track.