6 Channel Futaba 2.4 Ghz Fasst Receiver Compatible SBUS 3PM 3PKS 3VCS 3GR 4PKS Corona R6FA-SB

R6FA-SB receiver compatible with Futaba 3PKS , TM10,TM14, etc . If you are not sure if your transmitter can be compatible with our receiver pls contact us before your order .

The MAX voltage is 10v when you used this receiver  .

We highly recommend you set failsafe feature before flying your models. An example of a minimal useful, failsafe setting would be to shut down the model’s throttle, so that it does not fly or drive away uncontrolled.

Compatibility:

The CORONA 2.4GHz Spread Spectrum FASST Compatible Receiver is designed for use with FUTABA’s FASST 2.4GHz transmitters; including the 3PM,3PKS,3VCS,3GR,4PK(S),TM7, TM8, TM10, TM14 and the T6EX-2.4G, 7C-2.4G, 8FG, 10CG, 12FG. The R4FA-SB and R6FA-SB receivers supply a more useful mode for users. Both the R4FA-SB and R6FA-SB support FUTABA’s FASST air system and surface system. The R4FA-SB supports 7-channel with continuous PPM (positive and negative) output ,RSSI output and S.BUS output, R6FA-SB supports 6 channel high speed PPM(HS) mode to optimize helicopter response control and S.BUS output.

Under S.BUS output mode, both R4FA-SB and R6FA-SB supply 12 proportional channels and 2 DG channels. Therefore, the R4FA-SB or R6FA-SB becomes 14-channel receivers when using S.BUS output.   

Latency:

7mS for independent 6 channel (HS) output@ FASST multi-channel mode

14mS for independent 7 channel (LS) output and S.BUS output @ FASST multi-channel mode

8ms for independent 6 channel (HS) output@ FASST 7ch mode

16mS for independent 7 channel (LS) output and S.BUS output @ FASST 7ch mode

14ms for independent 3 channel output@ FASST surface system C1 CODE mode

Specifications:

Operating Current: 50mA max

Operating Voltage: 3.6 ~10V

Latency: R4FA-SB’s description 

14mS for independent 4 channel output and S.BUS output @ FASST multi-channel mode

21mS for Continuous PPM output and RSSI output@ FASST multi-channel mode

16mS for independent 4 channel output and S.BUS output @ FASST 7ch mode

24mS for Continuous PPM output and RSSI output@ FASST 7ch mode

14mS for independent 3 channel output@ FASST surface system C1 CODE mode

R6FA-SB’s description

7mS for independent 6 channel (HS) output@ FASST multi-channel mode

14mS for independent 7 channel (LS) output and S.BUS output @ FASST multi-channel mode

8ms for independent 6 channel (HS) output@ FASST 7ch mode

16mS for independent 7 channel (LS) output and S.BUS output @ FASST 7ch mode

14ms for independent 3 channel output@ FASST surface system C1 CODE mode

Sensitivity: about -100dBm

Operation temperature:-10~80 deg C

Setup:

Bind procedure:

· Turn on the FASST transmitter

· Connect the battery to the receiver while pressing the receiver’s F/S button.

· The Dual-color LED’s will continuously cycle through the following:

o Red LED light (searching radio signal)

o Green LED light (acquired the radio signal)

o Red LED off (bind ok)

o Green LED flashes 10 times (ID stored in memory)

o Green LED lights solid (normal operation)

       Note: FASST surface systems take a bit more time to complete the bind procedure.