|
[China]
Trade Verify
Address: 3 FL., Yuan Yi Yuan Industrial Park, QianJing Rd, XiXiang, BaoAn,ShenZhen, China
Contact name:Christina
Shenzhen Saef Technology Ltd. |
|
Verified Suppliers
|
|
|
0.63 Inch 120x28 Pixels OLED Display Module, 0.63 Inch OEL Matrix Display Product Introduction
SFOS063XZ-7114AN OLED Display Module is a 120x28 resolution COG graphic display, diagonal size 0.63 inch. The OLED model is designed as industrial grade which is having the advantage of competitive price. The module is built-in with SSD1312 IC; it supports I2C interface. The supply voltage for logic is 2.8V typical, ranging from 1.65V to 3.3V, supply voltage for display is 8V, Operating Current for VDD is 180μA, driving duty 1/28. SFOS063XZ-7114AN OEL Display Module is suitable for wearable device, smart home applications and etc. This module can be operating at temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃.
Features
9. This 0.63-inch OLED display has a faster response time of "10 microseconds at +25 °C".
10.This 0.63 inch mono OLED product has high brightness and this product has a contrast ratio of up to 2000:1.
11. This low cost 0.63 inch OLED product has lower power consumption - reducing CO2 emissions.
| Product: | 0.63 Inch OLED Display Module |
| Driver IC: | SSD1312 Or Equivalent |
| Interface: | I2C |
| Display Color: | Monochrome (white) |
| Number Of Pixels: | 120x28 Pixels |
| Display Mode: | Passive Matrix |
| Drive Duty: | 1/28 Duty |
| Panel Size: | 21.54 X 6.62 X 1.22 (mm) |
| Active Area: | 15.58 X 3.62 (mm) |
| Pixel Pitch: | 0.13 X 0.13 (mm) |
| Pixel Size: | 0.11 X 0.11 (mm) |
| Pin Number: | 14 Pins ( Can Be Customized) |
| Viewing Direction: | All Viewing Angles |
| Connection: | Soldering/Hotbar (customizable) |
| Life Time: | 50,000 Hours @60cd/m2 |
| Compliance: | REACH & RoHS Compliant |
0.63 Inch 120x28 Pixels OLED Display Module, 0.63 Inch OEL Matrix Display Product Drawing
Absolute Maximum Ratings
Optics Characteristics
Pin Definition
Pin1, C2P / Pin2, C2N / Pin3, C1P / Pin4, C1N
Positive Terminal of the Flying Inverting Capacitor, Negative Terminal of the Flying Boost Capacitor. The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
Pin5, VDD2 VBAT
Power Supply for DC/DC Converter Circuit. This is the power supply pin for the internal buffer of the DC/DC voltage converter.It must be connected to external source when the converter is used. It should beconnected to VDD when the converter is not used.
Pin6, VBREF NC
Pin7, VSS
Ground of Logic CircuitThis is a ground pin. It acts as a reference for the logic pins. It must beconnected to external ground.
Pin8, VDD1
Power Supply for Logic. This is a voltage supply pin. It must be connected to external source.
Pin9, RES#
Power Reset for Controller and Driver. This pin is reset signal input. When the pin is low, initialization of the chip isexecuted. Keep this pin pull high during normal operation.
Pin10, SCL
IIC Bus Clock Signal. The transmission if information in the I2C bus is following a clock sigmal. Eachtransmission of data bit is taken place during a single clock period of this pin.
Pin11, SDA
I2C Bus Data Signal. This pin acts as a communication channel between the transmitter and the receiver.
Pin12, IREF
Current Reference for Brightness Adjustment. This pin is segment current reference pin. A resistor should be connectedbetween this pin and VSS. Set the current at 12.5uA maximum.
Pin13, VCOMH
Voltage Output High Level for COM Signal. This pin is the input pin for the voltage output high level for COM signals. Acapacitor should be connected between this pin and VSS.
Pin14, VCC
Power Supply for OEL Panel. This is the most positive voltage supply pin of the chip. A stabilization capacitorshould be connected between this pin and VSS when the converter is used. Itmust be connected to external source when the converter is not used.
0.63 Inch 120x28 Pixels OLED Display Module, 0.63 Inch OEL Matrix Display Product Image
Factory Facilities and Certificates
SAEF Technology's graphic OLED display are available in three mechanical structures include COB, COG and TAB passive matrix technology. Available graphic monochrome OLED resolution in 50x16 OLED graphic display, 64x128 OLED, 100x16 OLED, 100x32 graphic OLED, 200x16 graphic OLED, OLED 128x32, OLED display 128x64, OLED 128x128, and 256x64 OLED Display. The graphic OLED display in the SAEF product range have on-board controllers and interfaces include parallel, serial, and I2C OLED, SPI OLED. These OLED display modules have driven voltages of 3V, or 5V depending on resolution/color.
SAEF offers a wide range of OLED display modules in sizes from
0.42" to 5.5" OLED, such as 0.42" micro OLED Display, 0.49" OLED
Display, 0.5" OLED Display, 0.54" OLED Display, 0.63" OLED Display,
0.66" mini OLED Display, 0.69" OLED, 0.91" OLED Display, 0.95"
OLED, 0.96" OLED Display, 1.5" OLED Display, 2" OLED , 2.4" OLED ,
2.7" OLED Display, 5.5" OLED Display, and custom design solutions.
Search Keyword:
96x32 oled, oled 96x32, 0.54 oled, 0.54" oled, 0.54 inch oled, oled 0.54", I2C OLED display 0.54, SPI OLED display 0.54, CH1115 OLED Display, SH1315 OLED,CH1115 OLED display, micro OLED, 0.54 inch mini OLED display, thin OLED display , tiny OLED display, round OLED display, color OLED display and OLED touch display.
Contact Us
We love to hear about your projects, If you have any questions, we can be reached at sales2@saef.com.cn
