Robot Automatic Laser Rust Cleaning Machine Easy Setting Laser
Cleaning Equipment No Damage To Material
Product parameters
| Items | Parameters |
| Cleaning Power | 200W |
| Current Consumption | Pout = Ponm / 5A |
| Max. Power | 900W |
| Power Voltage | AC 110/220V |
| Cooling Method | Air Cooling |
| Laser Class | Level 4 |
| Pulse Energy | 8mJ |
| Fiber Optical Cable | 5m(Customizable) |
| Laser Wavelength | 1064nm |
| Scan Width | 1-120mm |
| Preheat Time | 10-30s |
| Working Condition | A flat place without vibration and impact |
| Working Temperature | 0-60 ℃ |
| Storage Temperature | -10~+60℃ |
| Machine size | L647 x W 440 x H859mm |
| Net Weight | 70Kgs |
Safety alert
1) The power input is 220V, 50-60HZ
2) To make sure the power supply had connected the ground wire.
3) DO NOT aim the laser at the eyes, DO NOT watch the laser gun
mirror while the laser is on.
4) Do please turn off the button on the laser gun, and the laser
button on the screen when
you are going to stop the cleaning work, Or you are going to edit
the parameter settings.
5) Do please do not bend the fiber cable in a sharp turn.
6) Please wear protective glasses while using the machine.
Parameter Settings Instructions
● Galvanometer speed
The mirror swing speed is adjustable. The X mirror is 50HZ at the
fastest and 50/30 per gear. The Y mirror is 200HZ at the fastest
and 200/30 per gear.
● Laser frequency
Laser pulse frequency, 1K-200K optional.
● Laser power
Laser output power can be adjusted from 1 to 100.
● Laser pulse width
Use it while using an adjustable pulse width laser machine
● Graphic length (laser pattern is square)
The length of the laser beam. The maximum length is 120MM, and the
length can be adjusted freely within the 0-120mm range.
● Graphic width (laser pattern is square)
The width is up to 4MM, and the width can be adjusted freely within
the 0-40mm range.
● Filling pitch
The distance between lasers while cleaning with a circular laser.
● Opening delay and closing delay
When the laser galvanometer speed is too fast and the graphic
length is too long, the ideal effect can be achieved by setting the
switching light delay.
● Outer circle radius (laser pattern is a ring)
The max. outer radius of the graphic outer circle is 40 mm, and the
radius can be adjusted during the circular size. When the graph is
circular, the inner circle radius is set to 0.
● Inner circle radius (laser pattern is a ring)
The figure is a ring, and the radius of the inner circle can be set
up to 40MM (but not larger than the radius of the outer circle). In
this range, the radius can be adjusted to change the ring size.
● Application
While parameters were set in the interface. If you enable this set
of parameters, click Application.
● Save
After setting the parameters in the interface, remember to click
“Save” to save the parameters for the next direct use.
● Red light
When the button is pressed, the red button turns red and the red
light comes out. Press again and the red button will return to gray
and turn off the red light.
● Laser
Laser light button, press the button, the laser light comes out. If
the red light is emitted at this time, the laser will be forced
out. Press the laser button again to turn off the laser light and
the button will return to gray.
● Group
Mode selection, you can save nine sets of data. Click on the number
on the left side of the mode, you can select the set mode
parameters freely, click on the application. Remember to save the
data after the parameter wat set in each interface.
After-sales Service
1) 2 years quality warranty.
2) Lifetime maintenance free of charge.
3) Free training course for any application.
4) 24 hours of online service, free technical support.
5) The machine has been strictly tested and inspected before
delivery.
6) Door to door technical services(We have professional engineers
to offer machine installation
7)We can change a new machine if there is a quality problem that is
not easy to be solved.
