Shenzhen Mei Hui Optoelectronics Co., Ltd |
Verified Suppliers
|
|
BT1000 Skin Rejuvenation Face LED Red Light Therapy Panel
Naturally Erases Wrinkles
SPECIFIC & PROVEN WAVELENGTHS. MH-1000W red light device has 200pcs of 5w high power LEDs, 1:1 ratio of 660nm red, 850nm near infrared light. Red light is effective for boosting skin health and increasing collagen production. Infrared light can deliver energy to body cells to enhance muscle recovery, reduce pain and inflammation.
PRODUCT DIMENSIONS: 40.5*8.26*2.6inches; 14.3lbs. Power consumption: 250W. The greater the power consumption, the better effect you get. The MH-1000w delivers an irradiance of 105mW/cm2 at a distance of 6 inches. Low EMF output.
NATURAL. SAFE. NON-INVASIVE. 60 degree beam angle. 0 EMF at 3 inches. Low heat output for contact skin use. For both superficial & topical treatments as well as deep tissue treatments. Smart timer installed!
DURABLE & FLEXIBLE USE. MH-1000w device is a complete set, featuring a built-in cooling fan for heat dissipation. The MH-1000w device allows you to put it on the floor or hanging on the wall that delivers a (43.2"x10") treatment area.
Parameters
Light source | Simumen single core 5W |
LED quantity | 200pcs |
switch system | dual system |
Timing function | Yes |
Number of chips in each band of single module | light red light: 100PCS;Far red light: 100pcs |
Actual power | 1000W ±5% |
Input voltage | AC 85-265V50-60HZ |
Driving power supply | Isolated constant current |
Lens Angle | 60° |
Shell material | alloy frosted white |
Size | 900*205*70mm |
Standard accessories | power cord, hanging rope, eye mask |
ABOUT THE RED LIGHT THERAPY :
Q1. How does red light therapy work?
A: Red and red/infrared LED lights use ranges of wavelengths that
penetrate the outer layer of the skin, providing the cells with
usable energy. This brings about various reactions in the cells
including improved healing, the reduction of inflammation and
enhanced production of collagen.
Q2. How long does it take for red light therapy to work?
A: It is not an immediate miracle transformation that will occur
overnight, but it will provide you with ongoing improvements that
you will begin to see in anywhere from 24 hours to 2 months,
depending on the condition, its severity, and how regularly the
light is used.
Q3. What is the difference between red and near infrared light
therapy?
A: Red and near infrared light therapy are exactly the same except
for two differences: Red light is visible and near infrared
light is invisible. Near infrared light penetrates into the body
deeper than red light.
Q4. How often do I need to use red light therapy?
A: This depends on the condition you are treating and the device
you are using. For most conditions, daily use for at least two
weeks is recommended, followed by a once- or twice- weekly
maintenance regimen.
Q5. Do I need to continue to use the light as much when I start
seeing results?
A: Yes. Just because you're seeing results, it doesn't mean that
your skin cells are finished doing their jobs. It's just that the
results of their efforts are starting to become something you can
see and/or feel. Keep up the treatments until you reach your goal
level of results. Then you can start a weekly maintenance schedule.
Q6. Once my skin problems have been resolved, do I stop using the
light?
A: When your skin is clear or your fine lines, wrinkles, or
scarring have been reduced or even eliminated, it is best that you
continue the use of the light once or twice per week as a part of a
regular maintenance practice. This will help to make sure that the
benefits will continue over the long-term.
Matters needing attention
1. The lamp can not be used in dripping water or any wet place,
water and static electricity will damage the lamp; .
2. The working environment of lamps is -20~40℃,45%RH~90%RH.
3. In order to protect the lamps and lanterns, please disconnect
the power when lightning strikes.
4. Do not move the lamp under working condition.
FAQ
Q1. Can I have a sample order for led therapy light?
A: Yes, we welcome sample order to test and check quality. MOQ is 1
pc.
Q2. What about the lead time?
A: Sample needs 3-5 days, mass production time needs 1-2 weeks for
order quantity more than 50pcs
Q3. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5
days to arrive. Airline and sea shipping also optional.
Q4. Do you offer guarantee for the products?
A: Yes, we offer 3 years warranty to our products.
Q5. Can I print my logo on the unit?
A: Yes, we supply OEM and ODM service with small MOQ.