Home Companies Xi 'an West Control Internet Of Things Technology Co., Ltd.

NYWBUK Microwave Level Sensor Solid Powder 2.5MPa IP67

Xi 'an West Control Internet Of Things Technology Co., Ltd.

Contact Us

[China] country

Trade Verify

Address: Block V5, Ronghao Industrial Town, Gaoling District, Xi'an City, Shaanxi Province

Contact name:Gao

Inquir Now

Xi 'an West Control Internet Of Things Technology Co., Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

NYWBUK Microwave Level Sensor Solid Powder 2.5MPa IP67

Country/Region china
City & Province Shaanxi
InquireNow

Product Details

 

NYWBUK Microwave Level Switch Non-Contact Liquid Level Alarm​

 

NYWBUK series of microwave level switches are based on the principle of microwave very narrow pulse detection. Microwave level switch is a solid position switch designed by microwave pair emitter-receiver. The microwave level switch is a paired set of instruments, one end is the transmitter, the other is the receiving end, which is responsible for the acquisition and output of the microwave signal, and the instrument is installed in pairs on the position to be monitored. When there is no material plugging in the monitoring position, the receiving end outputs the Mno material” signal, and when the monitoring position is blocked, the receiving end outputs the "material plugging1' signal. The state of the output signal can be set to high bit alarm and low level alarm on the spot. Police.

 

NYWBUK Microwave Level SwitchTechnical Parameter

 

Applicationssolid powder / particle
Material304/316L Stainless steel(optional)
Power supply24VDC, 220VAC (optional)
Process temperature-40~80℃
Process pressure-0.1~ 2.5MPa
Process connectionThread, flange (optional)
Time delay0.5〜30s adjustable
Sensitivity0〜15 level
Measuring distance120m
Protection gradeIP67
Explosion-proof gradeExia IICT6 (optional)

 

※ Note: Products can be customized according to the specific requirements of users!

NYWBUK Microwave Level Switch Installation requirements
 
  • Do not damage the insulation of the probe during installation. Avoid mechanical wear of probe and installation interface, container wall, material etc.
  • The instrument guard line pipe must not have the stagnant water, otherwise will endanger the instrument electronic unit;
  • As shown in figure 1, due to the directionality of microwave emissions, the transmitter and receiver installed in the same group must be in the same direction, or reverse 180 °. When the position is 90 °, the receiving end will not receive a valid signal.
  • See figure 2. When multiple sets of microwave level switches need to be installed in adjacent locations, each adjacent set of instruments should be staggered 90 °. And keep the center distance above 500mm.
  • See figure 3 fbr a typical installation diagram.
  • Microwave level switches should be installed in pairs, one is the transmitter and the other is the receiver. The transmitter is responsible for transmitting the microwave signal and the receiving side is responsible for detecting the microwave signal and converting it to the level

Hot Products

Cast Aluminum Radar Level Transmitter Parabolic Antenna For Tank Height Measurement Radar Level ...
The radar level meter NYRD80X series sensor is a 26GHz high-frequency radar level measuring ...
26GHz NYRD-PB-B Flat Radar Level Meter The flat-panel radar level meter is a 26GHz high-frequency ...
NYRD701 Cable Type 1.8GHz Radar Level Meter Transmitter NYRD701 Cable Type 1.8GHz Radar Level Meter ...
Liquid Solid Powder Measure 80G Radar Level Meter Liquid Level Meter 80G Radar Level Meter Liquid ...
Liquid Level Meter Solid Powder Measure 80GHz Radar Level Mete FMCW Radar Products Liquid Level ...