|
[China]
Trade Verify
Address: Room 101, No. 21, Huayuanzai Road, Chongmei, Chashan Town, Dongguan City, Guangdong Province
Contact name:Huang
Dongguan Linkun Electronic Technology Co., Ltd. |
|
Verified Suppliers
|
|
|
3000～5000 OHM (4KΩ±25%) 700V 200MA PTC Overcurrent Protection Thermistor
MZ4 series PTC thermistors are used in various types of fluorescent lamps, electronic ballasts and electronic energy-saving lamps as preheating-starting components. Preheating of the electrodes lengthens the life of the lamps and the number of switching cycles significantly. Ampfort has been working at PTCR'S research, development and manufacturing for ten years. With rich experience, our company offers PTC thermistors for time delay and switching with high quality and reasonable price. Many lighting producers, including some famous international companies are our customers.
Features
1. PTC thermistor for time delay start of ballast & lamp could
extend the service life of the fluorescent tube by more than
10-time
2. PTC thermistor applied in various types of electronic
energy-saving lamp and fluorescent electronic ballasts
3. Switching current can pass over 100,000 times: the resistance
will not float
4. The withstanding voltage can reach to over 800-1,000V AC
5. High reliability, good performance of safety and stability
6. Application:Energy-saving lamp, fluorescent electronic ballasts,and digital multi-meters
| Number | Name | Technical Requirements | Leads |
| D | Diameter | 4.5max | □ Straight
□ Axis Formed
■ In-Forming |
| T | Thickness | 5.0max | |
| L | Lead Length | Min20 | |
| W | Distance between fuses | 5.0±0.5 | |
| d | Diameter of lead | 0.5±0.05 |
Coating Details
| Coating | Material | Color |
□ No coating ■ Coating | ■ PF resin □ Silicon
| ■ Yellow ■ Green |
Electrical Performances
| Number | Items | Technical Requirements | Test Conditions |
| 3-1 | Resistant for Zero Rated Power | 1200-1800Ω | Atmosphere Temperature:25±2℃ Accuracy of the Test:±0.5% |
| 3-2 | Over Voltage Withstanding | ≥600V ΔR/Rn≤20% No visual damage
| Starting Current:≥200mA, Starting Voltage:220VAC,hold on for 7s,and then change to high voltage800VAC,for 6s.the is shown as follows: Stay under the conditions of regular temperature and humidity for 4-5 hours, and then check the Rn again. |
| 3-3 | Over Current withstanding
| ≥200mA ΔR/Rn≤20% No visual damage | Starting Current:≥200mA,Voltage 220VAC, switch on the circuit for 1 minute after every 5minutes, switch-off, and repeat this operation for 20 times. Put it under the conditions of regular temperature and humidity for 4-5 hours and then check the Rn again |
| 3-5 | Curie Temperature | 75℃ | Check the temperature at 2 times Rn. |
Application Circuit
Other Performance
| Number |
Items | Technical Requirements | Test Conditions |
| 4-1 | Appearance | No noticeable defect, such as, bubbles and micro holes, etc; NO visible damage that may reduce its performance; the symbol is clear | Visual Check |
| 4-2 | Welding | It's tinned evenly and with smooth welds, and the tinned area 95% | Do the test according GB2423-28 of Ta, put welding aid on the faze end and soaked it into the 230℃ tin solution with only 5mm distance to the PTC body above the solution, and maintain for 3-5s. |
| 4-3 | Heat Resistance | Check the variation rate of resistance before and after the test ΔR/Rn≤20% | Do the test according to GB2423-28 of Tb stsy under the regular temperature and humidity for 4-5 hours, and then check the Rn again.Dipping terminals to a depth of 15mm in a soldering bath of 255℃±10℃,and to the place of 6mm far from PTC boby for 3±0.5s |
| 4-4 | Intensity of terminal | Check the variation rate of resistance before and after the test ΔR/Rn≤20% No Visual Damage No break out | Do the test according to GB2423-29 of U Test Ua: Fasten the body and apply a force gradually to each lead until 10N and then keep for 10sec.hold the body and apply a force to each lead until 90° slowly at 5N in the direction of lead axis and then keey for 10sec,and do this in the opposite direction repeat for other terminal. |
Characteristics
Contact Details:
Nancy Huang
Email: huangju@lk-ptc.
Tel/Whatsapp: +86 13423305709
Wechat: LinKun＿Nancy2013
QQ: 1078049901
