Active Member
|
[China]
Address: Room 602, building D, Huojuyuan , Yangguang Road, High-Tech District, Luoyang Area of China(henan) pilot free tradezone, henan Province, China.
Contact name:
Henan Duxin Science Technology Co.,Ltd. |
|
|
1. General Information
This specification defines the performance of rechargeable LiFePO4 battery pack describes the type, performance, technical characteristics, warning and caution of the battery pack.
2.
Specification
|
|
Customize Any of The Following Battery Packs as Required
Can be customized according to the requirements of 3.7V, 7.4V,
11.1V, 14.8V, 18.5V, 22.2V, 25.9V, 36V, 48V, 60V, 72V
BMS specification of 200Ah lithium battery 24 volts
rechargeable:
Cell overcharge detection voltage: 3.90V±50mV
Cell overcharge recovery voltage: 3.80V±100mV
Cell over-discharge recovery voltage: 2.30V±100mV
Rated operational charge current: 200 A
Over current detection: 100±30A
BMS impedance: ≤20mΩ
12V 100Ah advantage
Green product: LiFePO4 material is no harm to enviroment and human being .
Cycle life: More than 2000 cycle times
Very safe: It have the best safety and steady performance,no fire ,no exploding under the condition of over-charge.
Light weight and smaller dimension: The dimension compares with other battery.about 1/2-2/3 weight of lead acid
Great capacity and more powerful,rechargeable battery: We can install many single cells in series and in parallet and it can fully discharge
No memory effect: It can be recharged anytime,no reduction of the capacity
3.
Smart Lithium battery 12V 100Ah Electrical Characteristics &
Test Condition
@Testing Conditions: Ambient Temperature: 25±5℃; Huminity:45%~75%.
| NO | Items | Criterion | Condition | |
| 1 | Min Capacity | ≥97Ah | Rest for 1 hour after fully charged, then discharge with 0.33C current until the battery reaches the cutoff voltage. you can stop and define the Discharging current*time value (Ah) as battery capacity. | |
| 2 | Cycle life (DOD%100) | ≥2000cycle | Charge / CC(0.33C)/CV(14.6V); End current : 0.05C; Rest time : 1h; Discharge / CC(0.5C); End voltage : 8.0V; Repeat above process until discharge capacity is no more than 80% of normal value. Accumulated times is defined as cycle life. | |
| 3 | Discharge Temperature Characteristics | -20℃ | ≥70% | At 25±5℃ discharge the battery with the current of 0.33C to the cut-off voltage. Store the battery at various temperatures for 2h and discharge the battery with 0.33C to the cut-off voltage. Record the ratio between discharging & charging capacity. |
| 0℃ | ≥80% | |||
| 25℃ | 100% | |||
| 55℃ | ≥95% | |||
| 4 | Charge Retention ability | remain capacity≥90% | Charge the battery to full capacity and store it for 28days, and then discharge it with 0.33C to the cut-off voltage. | |
Safety Test
No fire, no explosion
Charing to 3.7v and do nail penetration test, there is no fire, no explosion, no any other obvious changes.
Nail Penetration Test and Overcharge Test
After testing, no fire and no explosion, that is definitely approved than our lithium batteries deserve you.
BATTERY PACK SAFETY TEST
4.1 Testing condition (Unless Special Requirements)
Temperature:20±5℃ Relative Humidity: 45~75%
Atmosphere Pressure: 86~106kPa
All testing under full capacity
4.2 Battery Pack Safety Test
| No. | Items | Standards | Testing Methods |
| 1 | Short-Circuit | The battery should be no remarkable breakage, distortion. And charge normally. | Use a resistor with less than 0.05Ω to make the battery short circuit for 1 hour. The appearance and characteristics are normal. |
| 2 | Over Discharge Protection Test | The battery should be no remarkable breakage, distortion. Appearance and charge are normal. | Discharge the battery at the rate of 20A with the load of 30Ω for 24h . Charging for 10sec with specified adapter , and check the voltage(≥16.0V) |
| 3 | Impact Test | The battery should be no explosion or catch fire | Place a full charged battery on a flat and put a stainless steel stick (Diamond 7.9mm) in the middle of the battery upright . Beat the steel stick with 9.1Kg |
4.
Circuit Protection
The batteries are supplied with a LiFePO4 Battery Management System (BMS)that can monitor and optimized each single prismatic cell during charge & discharge, to protect the battery pack overcharge, over discharge, short circuit. Overall, the BMS helps to ensure safe and accurate running.
| Test item | Content | Criterion |
| Over charge | Over-charge protection for each cell | 3.90±0.03V |
| Over-charge release for each cell | 3.60±0.05V | |
| Over-charge release method | Under the release voltage | |
| Over discharge | Over-discharge protection for each cell | 2.30±0.05V |
| Over-discharge release for each cell | 2.80±0.05V | |
| Over-discharge release method | Above the release value | |
| Over current | Discharge over current protection | 400±100A |
| Protection delay time | 50~200ms | |
| Over current release method | Release after cutoff the load. | |
Battery temperature | Battery Over temperature | Protection @65±5℃, Release @55±5℃ |
| Charge lower temperature | Protection @-10±5℃, Release @0±5℃ |
Application:
· Energy Storage Systems (ESS)
· Hybrid Grid back-up
· Remote area power systems
· Communications systems
· Electric vehicles
· Marine environments
· Military & Aviation
· Industrial Machinery
· Uninterruptible Power Supplies
· CCTV & Data Transfer
Warranty
• We offer 3 years warranty for battery packs in low discharge rate
(below 1C) applications,
• We offer 2 years warranty for battery packs in high discharge
rate (1~3C) applications.
• For charger / BMS, here are one year warranty.
Store
◆For long time storage ,the battery should be charged to Approx 60% SOC ,its corresponding voltage should be 1.05times of nominal voltage(24V,36V,60Vor72V),usually it's voltage in shipment .The battery should be kept in storage in dry and ventilated place.
◆ The battery pack and charger should be stored in clean, dry and ventilated place, avoid contacting with corrosive materials and be away from fire and heat.
Quality Control
We do below test before delivering
Capacity test, High current discharge test,Low temperature test, Short circuit test, Over charging test,
Over discharging test, Cycle performance test, Crush test, Impact test, Vibration test, High temperature test
Our Services
• By Air Door to Door Service
• By Sea Door to Door Service
• By Express: EMS, TNT, UPS, FedEx
FAQ
1. What's your advantage?
Small order is acceptable, zero risk, quality assurance.
2. Can you accept OEM and ODM services?
Yes, just tell me your requirements and we will provide you with
the best solution.
3. What are your payment channels?
TT, L/C, West Union etc.
4. What service do you provide?
All our batteries have passed the safe test and performance test
before shipment.
Support printing your logo on the battery.
Small order is acceptable.
5. Is your lithium battery reliable?
Yes. Overcharged, over-discharged, nail penetration test, all
protected by our battery.
6. Can I get a lower price if I order large quantities?
Yes, very competitive prices with more quantity.
7. How you shipping the goods and how long it will take?
Normally FEDEX, DHL,UPS etc, around 4-7 days.
8. Can I just try samples for the first order?
Yes, 1 pcs sample and small trial order are acceptable.
24 hours customer service, waiting for your inquiry!
