PSB1205-9 DC12V 5A 9Channels CCTV Distributed Boxed Switch Mode Power Supply

Item

12V DC, 5A, 9 Channels Boxed CCTV Power Supply

Model

PSB1205-9

Output

Voltage

12 V

Current (Rated)

5 A

Power (Rated)

60 W

Output Port

9

Ripple/Noise (Max.)

150mVp-p

Voltage (Adjust Range)

4.75-5.5 V

Voltage Accuracy

±2.0%

Line Regulation

±1.5%

Load Regulation

±1.5%

Time(Start, Rise, Hold)

1000ms, 30ms/230VAC, 1000ms,30ms/115VAC(Full-Load)

Input

Voltage (Range)

85-264 V AC

120-370 V DC

Frequency (Range)

47-63 Hz

Efficiency (Typ)

79%

81%

AC Current

0.3A/115V AC

0.25A/230V AC

Surge Current

Cold boot: 40A/100V AC

80A/230V AC

Leakage Current (Max)

<2mA/240V AC

Protection

Over Load

Not over 105% rated output power

Mode: Hiccup Mode, Recover after removing the over-load

Over Voltage

5.75-6.75V

13.8-16.2V

Mode: Shut down the output, Zener diode clamp

Over Temperature

Protection will be triggered when the temperature of connect point inside the transistor over 140℃

Mode: Shut down the output, Auto-recover after the temperature return to normal value.

Environment

Operate Temperature

-20 ~ 60 ℃

Operate Humidity

20 ~ 90%RH, no condensing

Storage Temperature

-40% ~ 85 ℃

Storage Humidity

10% ~ 95%RH, no condensing

Temperature Factor

±0.03%/℃(0 ~ 45℃)

Vibration Resistance

10 ~ 500Hz, 2G10mins/cycle,  X,Y,Z axis each 60 minutes

Safety & EMC

Safety Specification

UL60950-1, CB(IEC60950-1), CCC GB4943.1:2011 Approved

Electric Strength

I/P ~ O/P:3KVDC; I/P ~ FG:2KVDC; 0/P ~ FG:0.5KVDC

Insulation Resistance

I/P ~ O/P , I/P ~ FG , 0/P ~ FG:100M Ohms/500VDC/25℃/70%RH

EMC Radiation

Conform to EN55022(CISPR22) ClassB, EN61000-3-2,3

EMC Immunity

Conform to EN61000-4-2,3,4,5,6,11,EN55024,EN61000-6-1, A level QB SG

MTBF

≥563.5Khrs MIL-HDBK-217F(25℃)

Note

1. All specs and parameter, in the absence of special note, are measured base on 230VAC Input, Rate Loading, 25℃, 70%RH environment.

2. Volts D.C. Measuring Method: measure at the end of plug-in terminal under 50% loading condition

3. Ripple/Noise measuring method: Use a 12" twisted pair and terminal parallel connecting with 0.1uf and 47uf capacitance and measure in 20MHZ bandwidth

4. Accuracy: Include assigned error, Line regulation, Load regulation

5. Line Regulation Measurement: Measure range from low voltage to high voltage under rated loading

6. Load Regulation Measurement: Measure range from 0% to 100%

7. According to the rule GB4943.1, power supply only applicable in the place where elevation lower than 2000m and non-tropical climate area safely

8. Power supply shall be deemed to be part of system components, so it has to be applied based on electromagnetic related confirmation.