Home Companies BOGEN PUMPS

Explosion Proof Pneumatic Diaphragm Pump For Corrosive Liquids , Granular Liquids

Contact Us

[China]

Trade Verify

Address: E 18Floor Fazhan Build No.13 Easy Huayuan Road Chancheng Area Foshan City.

Contact name:ALLSON

BOGEN PUMPS

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

Explosion Proof Pneumatic Diaphragm Pump For Corrosive Liquids , Granular Liquids

Country/Region	china
City & Province	foshan guangdong
Categories	Pumps

Product Details

Explosion Proof Pneumatic Diaphragm Pump For Corrosive Liquids , Granular Liquids

Pneumatic Diaphragm Pump Introduction

pneumatic diaphragm pump is a new type of pump developed in China.Using compressed air as the power source, all kinds of corrosive liquids, granular liquids, high viscosity, volatile, inflammable, highly toxic liquids can be exhausted by light absorption.

Corrosion resistance high temperature resistance high pressure strong suction easy installation,No noise, no sparks.

Pneumatic Diaphragm Pump Parameters

Item	Description	Unit	Reference Figure
1	Maximum air inlet pressure	Mpa	0.83
2	Maximum flow rate	L/Min	903
3	Maximum lift	M	70
4	Maximum outlet pressure	Mpa	0.83
5	Maximum particle size	mm	9
6	Weight	kg	103
7	Noise level	db	＜70

A 50 X X - X X X - X (model selection)

Form of pipe mouth:A-BSP B-NPT(F) C-Flange

Diaphragm material:9 – Santoprene H – Hytrel T - PTFE/Santoprene

Ball material:9 -Santoprene H – Hytre T – PTFE A - Acetal

Ball seat material:P/K –Polypropylene/Kynoar SS –Stainless Steel

Pump material: SS –Stainless Steel AL –Aluminum Alloy CI- Carbon Steel P/K –Polypropylene/Kynoar

Pneumatic Diaphragm Pump Details

Maximum Applied Temperature Limits (diaphragm / ball / seal material)

Acetal ··············································· 40°- 150°F (4.4- 65.5°C)

Santoprene··········································-40°- 225°F (-40°- 107.2°C) ················································ ·40°- 220°F (4.4°- 104°C) Nitrile·················································10°- 180°F (-12°- 82°C) Viton···················································-40°- 350°F (-40°-176.6°C) Hytrel··················································-20°-150°F (-12°- 93°C) Kynar···················································10°-200°F (-28.9°- 65.5°C) Polypropylene·········································32°- 175°F (0-79.4°C)

Requirements for Air and Lubrication

EXCESSIVE AIR PRESSURE. Can cause pump damage, personal injury or property damage.

A filter capable of filtering out particles larger than 50 microns should be used on the air supply. There is no lubrication required other than the “O” ring lubricant which is applied during assembly or repair.
If lubricated air is present, make sure that it is compatible with the “O” rings and seals in the air motor section of the pump.

Maintenance

Please refer to the component schematic in the assembly drawings to look up the serial numbers and names of parts and grasp the information of parts and maintenance service pack.
Some BSK parts are marked as "wearing parts", which can conduce to quick service and downtime reduction.
Service kits are divided to service two separate diaphragm pump functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SEC -TION is divided further to match typical part MATERIAL OPTIONS.
Provide a clean work surface to protect sensitive internal moving parts from contamination from dirt and foreign matter during service disassembly and reassembly.
Keep good records of service activity and include pump in preven -tive maintenance program.
Before disassembling, empty captured material in the outlet man -ifold by turning the pump upside down to drain material from the pump.

Installation dimensions: