Home Companies Qingdao Huashida Machinery Co., Ltd.

3LPE Coating Pipe Production Line Joint PE Heat Shrinkable Sleeve 35 Mpa

Qingdao Huashida Machinery Co., Ltd.

Contact Us

[China] country

Trade Verify

Address: 69 Jinsheng Second Road Chengyang District, Qingdao, Shandong, China

Contact name:Lily

Inquir Now

Qingdao Huashida Machinery Co., Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

3LPE Coating Pipe Production Line Joint PE Heat Shrinkable Sleeve 35 Mpa

Country/Region china
City & Province qingdao shandong
Categories Belt Making Machinery Parts
InquireNow

Product Details

3LPE coating pipe production line Joint PE Heat Shrinkable Sleeve,solid and durable
 
 

It is mainly composed of base material and hot melt adhesive. Our company adopts unique hot melt adhesive formula to ensure the adhesive strength of the product in use and thus ensure the construction quality. Optimization of the design of the new heat shrinkable tape (set) is easy to site construction, fast shrinkage, short operating time, low construction costs, with excellent water vapor permeability, chemical corrosion resistance, insulation and aging resistance and other properties, is the ideal material for pipeline anticorrosion thermal insulation system. Among them, three layers of reinforced fiber type heat shrinkable tape (set) is in a layer of substrate, a layer of adhesive coating between a layer of reinforced fibers, adhesive strength and higher tensile strength, contraction faster, the effect is also better. Mainly used for oil and gas pipeline joints to fill the mouth of the anticorrosion, patching, can also be used for pipeline damage repair. This product is suitable for 3PE steel pipe, 2PE steel pipe, epoxy powder coating, thermal insulation pipe jacket skin and polyethylene drainage and sewage pipeline pipeline patching, patching.

Translated with DeepL.com 

 ITEMStandardUNITData
Adhesivesoftening pointASTM E 28°C70-80
shear strengthDIN 30 672N/cm≥100
Basicspecific densityASTM D792r/cm 30.935-0.96
tensile strengthASTM D638Mpa15-20
Elongation at breakASTM D792%350
hardnessASTM D2240ball48
Heat Shrinkable Sleevepeel strengthASTM D1000N/cm>150
water-intake rateASTM D570%0.05

 

Move the heat shrink sleeve to the centered position at the joint and take out the isolation material. Heat evenly from the center along the circumference, make it shrink completely and then extend the heating to both ends respectively. Pay attention to the even fire. After all the shrinkage is completed, reheat the uneven surface to make it completely flat. After the overall heating is completed, turn down the flame and reheat again to make the hot melt adhesive fully overflow. During the heating process, use the pressure roller to roll the joint several times, focusing on rolling the fusion lap to eliminate air bubbles.
Feature
1.Fast shrinkage speed,
2.good waterproof performance,
3 good anti-corrosive performance,
4.long service life, convenient transportation and fast construction.



2. 3Layer Fiber

reinforced PE heat shrinkable tape (sleeve) is composed of cross-linked polyethylene back, a middle layer of fiber and special heat melt adhesive an. The 3 layer reinforced sleeve gives better shrink ratio, and better strength. It is resistant to corrosion, wear, impact, UV and aging, easier to be operated.
Application area:
It is mainly used for Hollow wall spiral pipe, corrugated pipe and metal reinforced corrugated spiral pipe etc.

TEST PROCEDURE
1. Clean the steel pipe and heat it by fire till over 80 ºC
2. Paint the steel pipe with Primer (mixed with A&B)
3. Fire heat the heat shrink sleeve, be attention to start heating from middle of the sleeve, but act from up and down, and gradually move from middle to two sides of sleeve, in order to drive air out of the sleeve, after finish heating, the good result is that there is about 1-2mm hot adhesive melt at the edge of sleeve.

TEST RESULT
1. Test result after cooling about 40 minutes.
Peel strength to primer is over 100N per 2cm(till the end of the spring balance). at 30.7ºC
Co-adhesive: Half-half.
2. Test result after cooling about 24hours.
Peel strength to primer is over 172N per 2cm at room temperature about 30.7ºC
Co-adhesive: Half-half.
3. 2. Test result after cooling about 24hours.
Peel strength to primer is over 9.2kg/90N per 1cm at room temperature about 30.7ºC
Co-adhesive: Half-half.


PE Heat Shrinkable Sleeve Wholesale Pipe Joint Materials
 

Hot Products

Pipe Extruder HDPE Hollow Wall Corrugated Pipe Production Line Pipe Extruder HDPE Hollow Wall ...
Hollow Wall Corrugated Pipe Assembly Production Line China Factories manufacture Pipe Extruder HDPE ...
Customize Hollow Wall Corrugated Pipe Extruder Machine,Environmentally-friendly Pipe Extruder HDPE ...
Automated Hollow Wall Corrugated Pipe Extruder Machine,Complete in specifications Pipe Extruder HDPE ...
HDPE Hollow Wall Corrugated Pipe Extruder Machine Production Line,Easy to operate Pipe Extruder HDPE ...
Maneuverable HDPE Hollow Wall Corrugated Pipe Extrusion Line Plastic Extruder,Solid and durable Pipe ...