|
[China]
Trade Verify
Address: www.pcbseparator.com
Contact name:Alan
Dongguan Chuangwei Electronic Equipment Manufactory |
|
Verified Suppliers
|
|
|
Automated Dispensing Robot Machines Glue Dispenser Robot For Electronic Assembly Technical Parameters:
X/Y/Z Work Area: 300/300/100 MM
Work Load: Table/Tool: 10 kg./5 kg.
Max. Speed: X&Y/Z 800/320 (mm/sec)
Repeatability: +/- 0.02 mm/axis
Resolution: 0.001 mm/axis
Data Memory: 100 Programs/50,000 points per
Drive System: Micro stepping motor
Motion Control: Point to point & continuous path
Teaching Method: Teach Pendant
I/O Signals: 8 inputs/8 outputs
External Interface: USB/RS232
Power Supply: 100-240 VAC, 320W
Description:
The 300MM Stepper is our most popular industrial robot with a dispensing area of 11.81" x 11.81" (300MM X 300MM). The 300MM Cartesian robot represents a substantial cost saving in comparison to similar desktop robots. Its overall footprint has a depth of less than 26 inches (640MM), suitable for an industrial bench. This line of robots is also available with a low cost vision system.
These benchtop industrial robots are ideal for automating a current dispensing application. With the various work areas offered almost every application can be fitted on one of the models in this series; 200, 300 or 400MM Robots.
A program consists of a series of instructions stored in the main unit, each instruction stored in a numbered memory address. An address may record a point location, X, Y, and Z axis value, point type or instruction which sets a certain parameter, such as a dispensing time or line speed.
Installation:
The automatic dispenser machine can satisfy various requirements
for dispensing, only need to choose different fixtures and math
with dispensing systems.
The following installation instruction is based on the 30CC needle
cylinder clamp and simple type dispensing system as a model.
1. The standard accessories include the 30CC needle cylinder
clamps, and they can be applied to 30CC or 55CC needle cylinder. If
you want to use other needle cylinder, then you have to purchase
other needle cylinder clamps appropriate.
2. Fix the needle cylinder clamps onto the Z axle. Put the hexagon
socket flat head screws through the holes of the clamps and then
lock on the Z ground side. The clamp has a couple of holes to
select, according to the specific requirements .
3. Connect the signal port(three holes) of the dispenser machine on
the backside to the signal port in the controller with dispenser
signal line. The signal port in the dispenser machine is the same
one that connecting with the foot-plate. Thus a problem may appear
that the port can not be shared, if your dispenser machine is not
purchased along with the matching machine. In such case, please
contact the Extruder supplier for joint exchanging.
4. Connect the compressed air source to the dispenser controller,
put the needle cylinder collet onto the needle cylinder and tighten
it, and put the needle cylinder into the needle cylinder clamps and
lock the screws which are used to fix the needle cylinder.( Please
don’t over tighten, in case of deformation. And once it deforms,
the piston then cannot fit with the inner side of the needle
cylinder, and cause air leakage.)
5. Connect the handheld programmer to the machine.
6. Connect the dispenser machine and the controller to 220V power
source.
7. Do make sure the pressure pipe of the needle cylinder collet and
the power source will not influence the motion of each axles and
working plate.
8. Congratulations for completing primary set of the dispenser
machine, please learn teaching mode operation according to the
following chapters.
Why us
1.Engineers available to service machinery oversea. | Engineers are available to be sent to freign countries to do
machinery training and offer technical support. |
2.Mature technique & forerunner to process makes high quality
machinery. | As largest manufactory in South China, we have 12 years experience
on PCB separator machines and soldering machines. pcb router
machine Our R&D team continuously upgrade the existing machines to meet
the market development trend. |
3.Effective customer service. pcb router machine | All of us together are stronger and wiser than any one of us
individually. To succeed, we must assume responsibility, cooperate
with fellow associates and withdepartments, effectively comminicate
with one another, foster enthusiam and participate in
decision-making. To be seay reachable by customers and provide
prompt replies to solve their problems and create value for
customers. |
4.One year warranty for the machines except accessories. b
router machine | Robust frame construction and Japanese steel blades obtained good
appraise and recognized by and oversea clients. We offer parts for
replacement under warranty free of charge, clients only need to
bear freight charge. |
Our mission: | Ongoing PCB industry PCB separator technological innovation, to
create greater value, allowing customers to success |
Our Vision: | PCB industry to become the world's leading solution providers PCB
separator. pcb router machine |
