Active Member
|
[China]
Address: ROOM 2204, NO.98， TIANGAO ALLEY, SOUTH BUSINESS DISTRICT, YINZHOU, 315194, NINGBO, CHINA
Contact name:Roy Zhang
Ningbo Anyo Import & Export Co., Ltd. |
|
|
RVS28 dual unit 28mm rotary potentiometer for welding machine
Description:
Potentiometers and Rheostats create a change in their resistive value when a connected shaft is physically rotated
The name “potentiometer” is a combination of the words Potential
Difference and Metering, which came from the early days of
electronics development. It was thought then that adjusting large
wirewound resistive coils metered or measured out a set amount of
potential difference making it a type of voltage-metering device.
Today, potentiometers are much smaller and much more accurate than
those early large and bulky variable resistances, and as with most
electronic components, there are many different types and names
ranging from variable resistor, preset, trimmer, rheostat and of
course variable potentiometer.
| Rotation life | After 10,000 rotation after the test, the changes impacted no more than ± (15% R +0.5 Ω) rotational noise of not more than 100 mv |
| Terminal strength | After welding (350℃, 3,5 seconds) after the of terminal contacts should be good, no termination loosening of |
| Soldering ability | Dip the terminals into tin tank at 235°C±5°C for 5±0.5 seconds, the soldering area should be more than 90%. |
Mechanical specifications:
| Total rotation angel | The angle is measured by rotating shaft from the end of terminal R1 to the end of terminal R3. | 260°±10° |
| Rotation torque | Rotational torque when turn the shaft :without special provision,rotational speed is 60°/s in ambient temperature 5-35℃ | 20-200gf.cm |
| Stop torque | The force that shaft transfer from terminal 1 to stop point or terminal 3 to stop point after 10 seconds until be break | ≥5kgf.cm |
Electrical specifications:
| Total resistance | Measurement shall be made by the resistance between terminal R1and R3. | 1KΩ |
| Resistance taper | Resistance changes | B |
| Total Resistance tolerance | Measurement shall be made by the resistance tolerance between terminal R1 and R3. | ± 20% |
| Rated power | Rated power is based on continuous full load operation at the maximum voltage between terminal R1 and R3. | 0.5W(50 ℃) |
| Residual resistance | Test residual resistance beteen terminal R1 and R2; terminal R2 and R3 | R≤10KΩ R0≤20Ω 10KΩ<R≤100KΩ R0≤30Ω 100KΩ<R≤250KΩ R0≤50Ω R≥250KΩ R0≤0.1% |
| Rotation of noise | The murmur will appear when shaft turn from terminal 1 to terminal 3 by 30 rounds/minute equably speed. | ≤47mV |
| Voltage proof | Input more then one minute voltage between terminals and shell. | 2000VAC |
| Max. operation voltage | Maximal voltage which sustained by terminal R1 and R3 | 50VAC |
| Operating temperature | Potentiometer of the performance guarantee for the use ambient temperature | -30℃~70℃ |
| Insulation resistance | Test voltage:DC 500V, Test position: Between terminal and case | 200MΩ |
Resistance SR code table:
| Resistance | Code |
| 100Ω | 101 |
| 500Ω | 501 |
| 1KΩ | 102 |
| 2KΩ | 202 |
| 3.3KΩ | 332 |
| 4.7KΩ | 472 |
| 5KΩ | 502 |
| 10KΩ | 103 |
| 20KΩ | 203 |
| 22KΩ | 223 |
| 47KΩ | 473 |
| 50KΩ | 503 |
| 100KΩ | 104 |
| 200KΩ | 204 |
| 250KΩ | 254 |
| 500KΩ | 504 |
| 1MΩ | 105 |
| 2MΩ | 205 |
| 2.2MΩ | 225 |
Dimension:
