Waste Tree Branches Garden Wood Pallet Chipping Machine
Our tree branches wood chipping machine is a combination of
traditional chipping raw materials and modern technology, compared
with other manufacturers of equipment with high efficiency,
environmental protection and energy saving, high value-added
products, no loss, no noise, physical chipping without heating, do
not add any chemical raw materials, do not need to clear wood, easy
to operate, no wearing parts, long service life and so on.
Tree branches wood chipping machine parameter
Tree branches wood chipping machine |
Model | TYXP-215 | TYXP-216 | TYXP-218 | TYXP-2113 |
Feeding port size (mm) | 160*400 | 230*590 | 300*680 | 450*700 |
Fly-cutter qty (piece) | 2-3 | 2-3 | 2-3 | 2-3 |
Revolving speed (rotate/minute) | 592 | 590 | 650 | 500 |
Feeding raw materials max diameter (mm) | 160 | 230 | 300 | 450 |
Chip size (mm) | 30 | 30 | 30 | 38 |
Production capacity (ton) | 3-5 | 8-10 | 14-18 | 15-30 |
Main motor power( kW) | 45 | 55 | 90-110 | 200-250 |
Feeder power (kW) | (2.2-3)*2 | (3-4)*2 | (4-5.5)*2 | 7.5*2 |
Oil pump motor power (kW) | 1.5 | 1.5 | 1.5 | 3 |
Conveyor power (kW) | 3 | 3 | 4 | 4 |
Weight (kg) | 2990 | 5030 | 7000 | 11840 |
Dimension(mm) | 1470*1550*970 | 1800*1900*1210 | 2200*2150*1500 | 3670*2517*2050 |
Tree branches wood chipping machine structure
The tree branches wood chipping machine is composed of machine
base, knife roller, upper and lower feeding mechanism, feeding
device and hydraulic buffer system, and electrical control system.
- Machine seat. The tree branches wood chipping machine base is made
of high-strength steel plate welded together, which is the support
base of the whole machine. The tree branches wood chipping machine
base support and the machine base are welded into one piece, which
is used to place the base knife base. The bottom knife of the wood
chip machine is fixed on the bottom knife seat by specially made
high strength bolts through the knife pressing block. The
undercutter base can be extracted freely through a hole in the wall
plate of the machine and is fixed to the machine base by two keys.
The chips from the chipper fall through the holes in the screen and
are discharged from the bottom of the base. Oversized chips can be
crushed again by the crusher bar mounted on the base of the
machine.
- Knife roller. The knife roller is the working part of the tree
branches wood chipping machine, which is made of steel plate welded
together (the small wood chip machine roller is the whole solid
structure). It has good steel and moment of inertia and is tested
for dynamic balance. The tree branches wood chipping
machine spindle and knife rolls are connected by locking
devices or flat keys. Its structure is simple, easy to assemble and
disassemble, and reliable to use. The two ends of the spindle are
supported by automatic self-aligning roller bearings, and the
bearing seat is fixed on the machine base. The tree branches wood
chipping machine is equipped with two flying knives on the knife
roller, which are fixed to the knife roller with specially made
flying knife bolts through the pressure block.
- Upper and lower feeding mechanism. The upper feeding mechanism of
the wood chip machine is composed of upper feed roller seat, feed
roller, feed roller shaft, swing shaft, reducer and so on. tree
branches wood chipping machine under the feeding mechanism consists
of feed rollers, support rollers and feed rollers shaft, reducer.
The feeding roller of the wood chip machine has larger diameter,
heavier weight and coarse teeth on the surface, which can compress
the raw material and make it enter into the cutting position with
balanced speed to ensure the length and quality of the chips, the
teeth of the upper and lower feeding rollers are staggered, so that
the chips can be cleaned.
- Feeding device. tree branches wood chipping machine feeding device
belt conveyor or vibrating feeder in two forms. Belt conveyor
consists of a head wheel, tail wheel, belt and frame. The head
wheel of the tree branches wood chipping machine is driven by
the lower feed roller shaft through the chain. The head pulley
drives the belt to feed the raw material into the feeding mouth.
The vibrating feeder consists of a feed chute, base and drive
section. The crank linkage is driven by a motor alone, and due to
the eccentric rotation the trough is dragged for simple harmonic
vibration, so that the raw material moves forward in the trough
into the feed opening.
- Hydraulic system. Supplied by hand oil pump to the oil cylinder, it
can start the cover to facilitate the replacement of the blade;
during maintenance it can lift the upper feed roller assembly to
facilitate the adjustment of the gap between the flying knife, the
bottom knife and the disassembly of the comb plate.
Tree branches wood chipping machine in the market is quite hot, the
competition is huge, our factory strives to do the best, to be able
to drum wood slicer more perfect improvement, for the benefit of
the wood processing industry.