Home Companies Shenzhen HAISEN Technology Co.,Ltd.

DC Solution Emergency Converter With Tiny Size And Battery Inside

Shenzhen HAISEN Technology Co.,Ltd.

Contact Us

[China] country

Trade Verify

Address: 13th Floor, C1 Building, Songshan Lake Intelligent Valley, Liaobu Town, Dongguan City, 523808, Guangdong.

Contact name:Evelyn Chow

Inquir Now

Shenzhen HAISEN Technology Co.,Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

DC Solution Emergency Converter With Tiny Size And Battery Inside

Country/Region china
City & Province dongguan guangdong
Categories Optoelectronic Displays
InquireNow

Product Details

 

DC solution emergency converter with tiny size and battery inside

 
Features

  • Constant output power
  • Used with lithium battery
  • Suits forLED fitting with external LED driver
  • Accessary test switch and LED indicator
  • Auto Testing-Self Diagnostic Operation
  • With multi-protection function:

​         -battery overcharge protection
         -battery over-discharge protection
         -output overload protection
         -short-circuit protection 
 
 
Parameter Table
 

Input voltage220-240 Vac 50/60Hz
Input Current0.06A(Max) 230V AC
Input Power
<2W @230Vac
Power Factor0.5
Output Voltage Range10-50VDC
Max.output current170mA
Battery charging current200mA(Max)
Battery charging time24h(Max)
Working temperature0-60°C
Maximum shell temperature75°C
Storage temperature-20-60°C 
Electric strength3000Vac 5mA(input to output)
IP RatingIP20
Warranty

3 Years 

 

 

Model Selection table
 

Model No.Input voltageOutput voltageEmergency powerLithium batteryEmergency timeOutput Current
ES-EOE01-01S220-240Vac 50/60Hz10-50V DC1W2000mAh/3.7V3Hrs100-20mA
ES-EOE02-01S220-240Vac 50/60Hz10-50V DC2W2500mAh/3.7V3Hrs100-20mA
ES-EOE03-01S220-240Vac 50/60Hz10-50V DC3W3000mAh/3.7V3Hrs100-20mA

 

 


Dimension (Unit:mm)


Wiring Diagram

Operation Instructions
1. Connect the wires according to the wiring diagram.
2. Power on L and N, and close the switch S1. At this time, the load light will turn on, the indicator light of the emergency power supply will turn green, and the emergency power supply is charged normally. Turn off this switch S1, the load light will go out.
3. Simulated emergency: close switch S1, turn on the load light, and then press the switch (TEST SWITCH), then switch to emergency power supply mode, the green light of the emergency power indicator will go out. Then  release the switch (TEST SWITCH), at this time it should be switched to external drive power supply, the green light of the emergency power indicator will light up.
4. Power failure and incoming call, the phenomenon should be the same as simulated emergency.

 


Battery Application Notice

1.The battery should be recharged and discharged semiannually in normal use conditions.
2.Do not connect to the circuit when the battery is not use to prevent over-discharge of the battery due to self-consumption of the circuit board.
3.Please keep the battery from the heat source when installing and using, and only be allowed to use in certain working temperature range.
4.The battery should be stored in a cool and dry environment.
5.After long time storage, the battery is cycled every 6 months as required.
 
 
 
 

Hot Products

The Microwave sensor HD05V-CRH with DIP switch and On/Off function HD05V-CRH .pdf Features Dual ...
Small Size DIP Swicth Sensor with UL And FCC Certification *HD401S 1 specification.pdf* Features: ...
Detached Design Dimmable Sensor HD405V-CRH with UL And FCC Certification *HD405V-CRH specification...
15M Highbay UL Sensor HD406VRH Suitable for UFO With On/Off Function *HD406VRH ON&OFF specification...
HD07VR-MH-B Highbay Bluetooth Sensor with UL Certification Dimmable Funnction *HD07VR-MH-B ...
HT36V Motion Sensr And Driver 2 in 1 Product with Dimmable Function *HT36V.pdf* Features: 5.8GHz ...