Wound Care Medical Dressing Pack Negative Pressure Suction Drain For Hospital

Wound Care Dressing Pack Negative Pressure Wound Drainage Set Wounds For Hospitals And Clinics

Product Introduction​

Applicable departments: trauma orthopedics, hand and foot surgery, spine surgery, burn plastic surgery, general surgery, emergency surgery

Consists of a drainage material and a multi-sided porous rigid drainage catheter that has been inserted into the foam. The space is large, and the clinical investigation shows that it can solve the problems of complex operation, air leakage and pipe blockage encountered in clinical practice.

Contraindication:

1. Patients with active bleeding on the wound;

2. Vascular diseases: patients with no blood supply to local tissues or venous thrombosis;

3. Patients whose body surface wounds cannot be closed with medical semi-permeable membranes;

4. Patients who enter the chest or cranial wound;

5. Those who are allergic to polymer materials.

Relative contraindications (use with caution):

Patients with incomplete wound debridement or large amounts of necrotic material still produced.

Patients who require close observation of changes in wound condition.

Black PU foam, adhesive film, suction connecting pipe, trapezoidal joint, suction cup joint, Y joint,
Liquid stop clip, non-porous connecting tube. Porous flush tube

White PVA foam straight tube type
White PVA foam suction cup type

specification: (Length: 5 ~ 60cm) *( width :5 ~ 45cm) *( thickness: 0.6 ~ 4.0cm) (straight tube type, suction cup type)
Main performance indexes:
Products should be sterile;
For other main performance indicators, please refer to product technical requirements.

Structure: The wound therapy dressing consists of medical foams , transparent breathable adhesive membrane (hereinafter referred to as adhesive membrane), suction connection tube, porous suction tube,Porous flushing tube, non-porous connection tube ,trapezoidal joint, suction cup type joint, Y-joint, liquid stop clip, etc., And according to customer requirements, the combination of card is configured in the packaging box.

​4.1 Medical foam
4.1.1 PVA foam: Honeycombed, with good three-dimensional structure and space, good permeability and water permeability, strong resilience and good biocompatibility. Physical properties: shrink and harden when the product is dry. Therefore, compared with PU foam, PVA foam is more suitable for wounds with more acute secretions with high negative pressure drainage.
4.1.2 PU foam: Composed of numerous filaments, the three-dimensional network is better in three-dimensional structure and space than PVA foam, and the density is only 1/3--1/5 of PVA foam. More breathable and permeable, excellent biocompatibility. Compared with PVA foam, PU foam is more suitable for the negative pressure sealing treatment of wounds with less dryness of various secretions and chronic refractory wounds.
4.2 porous suction tube
Silica gel material, cloth into the foam to enhance the drainage effect, strong compression resistance, according to the width and length of the foam to determine the number of porous suction tube and tube arrangement mode.
4.3 Porous flushing tube
Silica gel material, cloth into the foam to play the role of washing the wound surface, according to the width and length of the foam to determine the number and mode of porous suction tube.
4.4 Non-perforated connection tube
PVC or silica gel material, one end is connected with the flush tube installed in the foam through the corresponding specification of the joint, and the other end is connected with the guide tube through the corresponding specification of the joint.
4.5 Transparent breathable adhesive membrane
Pasting is an important material for wound closure, and the pasting process is also a key step. If wound closure and leakage directly affect the therapeutic effect of negative pressure sealing and drainage. According to different types and specifications of protecting and creating materials, different types and specifications of laminating membrane can be configured. See instructions for details.
4.6 Suction connection tube
4.6.1 Universal suction connection tube: both ends of the connection tube are 6-7mm interfaces, which can be connected with 6-7mm universal joints.
4.6.2 Special suction connection tube: one end can be connected with the negative pressure bottle of intelligent wound negative pressure comprehensive treatment

​

​Scope of application
Straight tube foam sealing method:
In the mesenteric method, a single tube is generally pasted and sealed. When there are two or more tubes, it is more convenient and effective to use face-to-face pasting.
According to the wound area, size and shape, design the foam cutting, the drainage direction of the porous drainage tube or the suction cup joint, and the adhesive film sealing scheme.
As shown in the picture on the right: Cut the membrane to a width of 8--10cm, fold the centrifugal paper outward, then tear off the centrifugal paper, stick the folded edge of the folded membrane to the lower edge of the wound, place it on the wound foam, and paste the porous suction connection tube on folded film.
Apply an appropriately sized and collapsible membrane using a face-to-face paste and seal the entire wound.
8.6 Suction cup foam sealing method:
PU foam suction cup type and PVA foam suction cup type are different in structure and sealing method.
8.6.1 PU foam suction cup sealing method:
After the foam is cut, determine where the suction cup fittings will be placed on the foam and where the porous irrigation tube will enter the foam. Use a sterile scalpel to pierce the foam at an angle of 30-45 degrees, then touch the wound with sterile forceps, introduce the porous irrigation tube into the foam, and fix the porous irrigation tube in the foam by puncturing to play a certain role . Then, use two large suction cup membranes to seal the entire wound from the suction cup to the left or up.

Design foam cutting,

With the suction cup as the center, the entire wound surface is sealed with a special film made of PU sponge suction cup.

After connecting with negative pressure, the wound was checked to have no air leakage, and the wound pipeline was cleaned unobstructed under negative pressure.

8.6.2 PVA foam suction cup sealing method:
After cutting the foam, place it on the wound surface and seal it with PVA suction cup special membrane. First, let the flush tube interface on the suction cup go through the corresponding hole of the membrane, and then let the suction tube interface go through successively. Let the membrane stick close to the root of the flush tube and the suction tube, and then peel off the core paper from the upper and lower membrane of the suction cup and paste the fixed suction cup and foam respectively. The special adhesive membrane is closed from the center of the suction cup to the other end of the foam, and then the adhesive membrane is set under the suction cup interface and overlapped with the above adhesive membrane by cutting two notch, and the other end of the foam is closed downward.

After cutting the foam, place it on the wound surface and seal it with PVA suction cup special membrane. First, let the flush tube interface on the suction cup go through the corresponding hole of the membrane, and then let the suction tube interface go through successively.

Tube connection:
Y-joint, trapezoidal joint are used to connect various suction tubes in the medical foam according to functions.

​

​

​

​

1.What is advantage on quality?

The company is furnished with developed equipment and technology from Germany, Belgium, and Taiwan (area).

2. What is MOQ?
30,00 pcs, It depends on requirements of products.

3. How to place a order?
Place order with salesperson
Make payment for deposit;
Sample making for confirmation before mass production;
After sample confirmed, mass production start;
Goods are finished,inform buyer to make payment for balance;
Delivery.
Production time : 30-40 days.

4. What is your term of payment?
T/T is a regular payment (30% in advance, 70% before shipping).
Paypal and Western Union are just for a sample