Industrial Servo Motor SGMAS-02ACA21 200W Yaskawa Electric SGMAS
Sigma II
QUICK DETAILS
- Power : 200W
- Voltage: 200V
- Voltage : 1.9A
DESCRIPTION
- Industrial Servo Motor
- SGMAS Sigma II
- Motors-AC Servo
(1) Secure the servomotor. Secure the servomotor to mounting holes
to prevent it from moving during operation. Alternatively, install
the servomotor on the machine and disconnect couplings and belts.
(2) Disconnect connector 1CN, then check the motor wiring in the
power supply circuit. I/O signals (1CN) are not to be used so leave
connector 1CN disconnected.
Note: When absolute encoder is used, connect the battery. Also,
initialize the absolute encoder. See 3.8.5 Using an Absolute
Encoder for details.
(3) Short the alarm signal circuit. Because connector 1CN is
disconnected, the alarm signal prevents the power supply circuit
from being turned ON. Therefore, temporarily short the alarm signal
circuit.
(4) Turn the power ON. Turn the Servopack power ON. If the
Servopack is turned ON normally, the LED on the Digital Operator
lights up as shown in the figure. Power is not supplied to the
servomotor because the servo is OFF.
If an alarm display appears on the LED as shown in the figure
above, the power supply circuit, motor wiring or encoder wiring is
incorrect. In this case, turn the power OFF, then correct the
problem.
Note: When absolute encoder is used, perform the following
procedures after turning ON the power.
- Set the bit E of Cn−01 to 1.
- Set the number of encoder pulses (Cn−11) to 1024.
- Set the dividing ratio of encoder pulses (Cn−0A) to 1024 or below.
- Turn OFF the power once. Then turn ON the power again after
checking if the displays of digital operator extinguish.
(5) Operate using the Digital
Operator Operate the motor with the Digital Operator.
Check that the motor runs normally.
Refer to 4.2.2 Operating Using the Digital Operator.
(6) Connect signal lines. Connect connector 1CN as follows:
- Turn the power OFF.
- Retrun the alarm signal circuit shorted in the above stepto its
original state.
- Connect connector 1CN.
- Turn the power ON again.
![2kw Industrial Servo Motor For Sewing Machine SGMAS 02ACA21 1.9A Voltage 0](http://img.everychina.com/nimg/e1/4e/39a2eb8d6cd79450a7dacc77aec0.jpg)
![2kw Industrial Servo Motor For Sewing Machine SGMAS 02ACA21 1.9A Voltage 1](http://img.everychina.com/nimg/15/56/eeaf1b8116d2e7f34b5f81afc4e6.jpg)
![2kw Industrial Servo Motor For Sewing Machine SGMAS 02ACA21 1.9A Voltage 2](http://img.everychina.com/nimg/60/0f/20df21e474b9c6f6a84e46627de3.jpg)
![2kw Industrial Servo Motor For Sewing Machine SGMAS 02ACA21 1.9A Voltage 3](http://img.everychina.com/nimg/f0/a7/0c85594bb28457bc2d941a076ffc.jpg)
SIMILAR PRODUCTS
SGMAS-C2AGA-SU12 | SGMAS-A5A2A2C |
SGMAS-A5A2A4C | SGMAS-A5A2AH101 |
SGMAS-A5ABA-TE11 | SGMAS-C2A2A4C |
SGMAS-C2A2A6C | SGMAS-A5ACA2C |
SGMAS-C2ACA41 | SGMAS-C2ACA41-E |
SGMAS-A5ACA4C | SGMAS-C2ACA21-Y2 |
SGMAS-C2ACA21 | SGMAS-A5ACAJ121 |
SGMAS-C2A2A6C | SGMAS-C2ACA21 |
OTHER SUPERIOR PRODUCTS
Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
Honeywell TC-,TK- | GE Modules IC - |
Fanuc motor A0- | Yokogawa transmitter EJA- |
Contact person: Iris
E-mail: Iriss88@163.com
Cellphone: +0086-17728602038
Fixed line:0752-2222038
Wechat:18026552038
WhatsApp:+86 18026552038