Auto Polishing Head Single Disc 250mm Metallographic Grinding Polishing Machine 50-600rpm

Auto Polishing Head Single Disc 250mm Metallographic Grinding Polishing Machine 50-600rpm

Brief Introduction:

XGrind-317 automatic grinding and polishing machine adopts international advanced manufacturing technology in accordance with international standards.

XGrind-317 has the following features such as stable and reliable performance,easy operation.wide processing range and working process of the automation etc.It is an ideal sample preparation equipment.

Technical Parameters:

Surface layers damaged by cutting must be removed by grinding. Mounted specimens are ground with rotating discs of abrasive paper, for example wet silicon carbide paper. The coarseness of the paper is indicated by a number: the number of grains of silicon carbide per square inch. So, for example, 180 grit paper is coarser than 1200 grit.

The grinding procedure involves several stages, using a finer paper (higher number) each time. Each grinding stage removes the scratches from the previous coarser paper.

This can be easily achieved by orienting the specimen perpendicular to the previous scratches. Between each grade the specimen is washed thoroughly with soapy water to prevent contamination from coarser grit present on the specimen surface. Typically, the finest grade of paper used is the 1200, and once the only scratches left on the specimen are from this grade.

The series of photos below shows the progression of the specimen when ground with progressively finer paper.

Polishing discs are covered with soft cloth impregnated with abrasive diamond particles and an oily lubricant or water lubricant.

Particles of two different grades are used: a coarser polish - typically with diamond particles 6 microns in diameter which should remove the scratches produced from the finest grinding stage,

and a finer polish – typically with diamond particles 1 micron in diameter, to produce a smooth surface.

Before using a finer polishing wheel the specimen should be washed thoroughly with warm soapy water followed by alcohol to prevent contamination of the disc. The drying can be made quicker using a hot air drier.

Mechanical polishing will always leave a layer of disturbed material on the surface of the specimen. Electropolishing or chemical polishing can be used to remove this, leaving an undisturbed surface.

The metallographic grinding and polishing machine made by iqualitrol has passed CE certification. It features a sturdy and durable cast aluminum base, equipped with high-precision spindle and transmission mechanism, which effectively absorbs vibration during grinding and greatly increases comfort in use. It can obtain smoother grinding samples and reduce laboratory noise. The machine can be equipped with a fast magnetic adapter, compatible with various diamond grinding systems, facilitating quick switching of various grinding consumables and greatly expanding the scope of equipment applications.

The stainless steel ceramic faucet customized by a Taiwanese sanitary ware manufacturer is used to meet the special needs of metallographic grinding, including water flow rate and angle, while also being aesthetically pleasing and practical.

The drainage system adopts an anti-clogging triangular waterway design to solve the problem of clogging caused by grinding consumables for long-term users. We use the shortest waterway distance and angle design to reduce the probability of clogging.

The waterproof film panel has 9 sets of grinding and polishing parameter memory functions. Different grinding speeds, directions, and times can be set for different materials and requirements, which can be changed at any time to meet different grinding and polishing needs.

When used for automatic polishing, an automatic dripping device can be purchased to allow polishing consumables (diamond suspensions, alumina powder, final polishing liquid) to automatically drip onto the polishing disc according to the set time.

HPA-1 Metallographic Grinding Machine designed through various investigation and gathering opinions and requirements of various users. Adapt to the needs of grinding more material. The disc diameter greater than the domestic similar products. The speed of the mill is different from domestic products, is an excellent sample grinding equipment.

Grinding and polishing is the final stage in the metallographic sample preparation process and consists of several steps. Each step uses finer abrasive than the previous one, the ultimate goal being to produce a deformation-free, scratch-free and highly reflective sample surface. The sample may need to be examined, either etched or unetched, to reveal the microstructure of the material. It frequently happens that contrasts in the material are only visible after a successful etching step.

After a metallographic sample has been mounted, grinding and polishing creates a flat and even surface. Any potential residue from the mounting process or damage from the sectioning process are ground off to expose the actual microstructure of the sample. Polishing removes abrasions from the previous steps to provide a smooth surface. LECO grinding and polishing instruments ensure that metallographic instruments provide a reliably clean sample that will be ready for further analysis.