Wholesale price Horizontal Glass Washing Machine with best Quality
CP-2500A (12 m/min) glass washing machine technical parameters
1. Purpose:
CP-2500A Glass Washing Machine CP-2500A is used to wash and dry the
upper and lower surfaces of ordinary flat glass and high-quality
low-e glass. It consists of a feed section, a cleaning and air
drying section and a discharge section.
2. Structural features:
1. Aluminum alloy assembly structure, no waste concept, permanent
use,
High efficiency, energy saving 70%;
2. The remaining sheet metal parts are all advanced mechanical
spraying
Paint or powder
3. The rubber roller is made of vulcanized rubber with a stainless
steel shaft;
4. The washing part in contact with water is made of stainless
steel;
5. In the cleaning department, the air duct personnel are lifted as
a whole, the maximum lift: 350mm, easy to clean and maintain;
6. Three pairs of brushes (Ø150mm), stainless steel shaft structure
(low-e glass, ordinary coated glass and daylight coated glass can
be cleaned without damaging the coated surface);
7. Two pairs of special stainless steel and aluminum alloy air
knives are configured, with high wind power and good air drying
effect, with heating system (with temperature control device,
optional opening and closing);
8. An air filter is installed in the air inlet of the fan. The air
volume is large and the air drying effect is good. The entire air
box is installed in the upper part of the workshop, and the side is
equipped with an air filter for easy inspection and cleaning.
9. Gear drive, frequency conversion speed regulation, digital
display main drive, and the rotation of the brush roller in the
washing section are driven by independent belts of the upper and
lower motors respectively. The frequency conversion speed
regulation is stable, and the service life is long, realizing the
cleaning of special glass with high requirements;
10. Mechanical button control, digital display of washing machine,
simple operation, easy operation and easy maintenance;
11. Outside the water tank of the washing machine, it is convenient
to clean, change and inspect the water tank, so that the washing
effect of the washing machine is cleaner.
12. Optional PLC control, touch screen display, convenient for
workers to operate and maintain, and can be connected to all edging
machine manufacturers without gaps (purchase separately if
necessary)
3, Technical parameters:
1. Maximum glass width: 2500mm (effective maximum: 2650mm)
2. Minimum glass specification: 400mm×400mm (Limited row on left
and right)
3. Glass thickness: 3mm-25mm (digital display)
4. Speed range: the glass thickness is within 3-25mm, Vmax =
1-12m/min
5. Main drive, brush speed control mode: frequency conversion speed
control
6. Workbench height: 900±25mm
7. Total power: 42KW (with water wind heating: 15KW)
8. Water source: self-circulation, tap water (according to civil
water standards) and deionized water supplements (the buyer should
provide deionized water equipment)
9. Power supply: 380V 50Hz
10. Dimensions (length × width × height): about 6260 × 4800 × 3100
11. Weight: about 3940kg
| Maximum glass width | 2500mm (effective maximum: 2650mm) |
| Minimum glass specification | 400mm×400mm (limited to single row on left and right sides) |
| Glass thickness | 3mm-25mm (digital display) |
| Speed range | glass thickness within 3-25mm Vmax=1-12m/min |
| Main drive, brush speed regulation method | frequency control |
| Table height | 900±25mm |
| Total power | 42KW(water-bearing wind heating: 15KW) |
| Water source | self-circulation, tap water (according to civil water standards)
and deionized water water supplement (deionized water equipment
shall be provided by the buyer) |
| Power source | 380V 50Hz |
| Dimensions (length × width × height) | approximately 6260*4800*3100 |
| Weight | 3940kg |
