Material | Porcelain tile | | | |
Discription | modern stone mix tile,mold made anti slip ,R10 use at our door
gardon ,and in door the bathroom shower floor and wall , kitchen
floor and wall . |
Product Dimensions | 24 x 24 x 0.4 inches | | | |
Thickness | 10mm | | | |
Finish | lappato surface | | | |
pattern | marble stone and cement mix 12 random patterns | | | |
colors | black color , | | | |
Shade Variation | V4-substantial variation (Color Variation within each tile ) | | | |
Absorption rate | <0.05% | | | |
Abrasion resistance | 6 - commercial considerable traffic | | | |
Function | Chemical resistant and Frost resistant, Acid-resistant,
Antibacterial, Heat insulation, Wear-resistant | | | |
Usage | Use in indoor and outdoor floor and wall | | | |
Packaging | Standard cartons and wooden pallet | | | |
Size(mm) | Pcs/ctn | M2/ctn | Kg/ctn | Ctn/20’ |
600x600 24x24 | 4 | 1.44 | 33.5 | 820 |
300x600 12x24 | 8 | 1.44 | 33.5 | 820 |
300x300 12x12 | 11 | 1 | 23.3 | 1180 |
Guidelines: widely used in the living room, toilet, kitchen wall
floor, flagship store, can also be laid outdoors. |
Process characteristics: Can keep color for a long time, hard and
wearable, suitable for use in most indoor spaces except toilets and
kitchens. |
Glaze: Concave-convex grinding face plus flash glaze, non-slip,
easy to clean. |
Design pattern: Multiple patterns combination, can be mixed with
multiple colors. |
1, when opening the box, should recognize the product
specifications, dimensions, color number, etc., the same color
number of the product affixed to the same position, do not mix the
products of different color numbers together pasted(unless
consciously required to obtain |
Special decorative effects in the figure) |
2, before pasting first on the ground test, after using the same
color number and size, you can use the adjacent color number and
size, and different color number, size tile classification, and
then in the bottom of the brick for use |
Number to indicate. If the brick surface has a pattern or
directional pattern, the product should be unified according to the
direction of the pattern, in order to best decorative effects. |
3, at present, the tile pasting mostly uses wet pasting and dry
pasting two methods. |
4, when paving the floor brick, it is recommended that the surface
area of cement mortar paving should not be too large, so as not to
find the surface cement mortar more than the initial coagulation
time(about 45 minutes), resulting in the tile and adhesive layer
adhesion is not dense |
Real, causing quality problems such as air drums. |
5, when leaving seam pasting, polished brick spacing 2mm-5mm is
appropriate. The polished brick and the wall junction leave a seam
of 3mm-5mm. |
6, pasting should be carried out after the base is compacted. When
tiling tiles, the tiles and the pasting surface are first presented
at a certain angle(about 15 degrees), and then pushed gently to the
horizontal direction by hand to balance the bottom of the brick and
the pasting surface. |
This facilitates the elimination of bubbles; Then tap the brick
surface with a hammer handle, so that the bottom of the brick can
eat pulp, so as not to produce an empty drum phenomenon; Then knock
the brick surface to level with a wooden hammer and measure it with
a horizontal ruler to ensure |
The tile pasting level. |
7, the product pasted for about 1 hour(depending on the climate and
the degree of cement condensation), we must use the wood bran or
sponge to clean the cement mud in time, to avoid the surface
contamination time is too long, it is difficult to clean up. |
8, about 12 hours after the product is pasted, hit the ground with
a wooden hammer in time to check whether there is an empty drum
phenomenon. All brickwork should be done in time to remove the
surface dirt, 24 hours before walking. |
9, pasted tiles within 48 hours, it is best not to use large-scale
waxing and other electric equipment, so as not to tile and adhesive
layer later shock and lead to unnecessary empty drum phenomenon. |
|
Delivery: |
1. After payment, we will deliver the goods within in 7 days. If
there is any special circumstances, we will inform you in advance.
Ceramic goods are shipped through the logistics line. will inform
you ETA day . Individual regions need to transfer. The time will be
slightly longer. The actual arrival time is based on the logistics
company. |
2. Goods to your city, the logistics company will call you to the
logistics station to pick up goods. |
|