|
[China]
Trade Verify
Address: Room 202, Building 4-2, No. 539, Shibei Industrial Road, Dashi Street, Panyu District, Guangzhou, Guangdong
Contact name:Tessa Huang
Guangzhou HongCe Equipment Co., Ltd. |
|
Verified Suppliers
|
|
|
IEC 60529 IPX1 To IPX8 Waterproof Ingress Protection Test Equipment, 500L Water Tank
Nowadays, there are more and more electronic products used
outdoors, and waterproof test is a very important link for
products, because only after waterproof test can we have a basis to
judge whether the products manufactured by the factory can still
maintain stable performance in outdoor harsh conditions. Therefore,
IP waterproof grade test is an essential project.
The waterproof test is mainly applicable to the shell protection
grade test (IP waterproof grade test) of products in the fields of
electronics and electricians, lamps, electric cabinets, electronic
components, automobiles, transportation, external devices and so
on. Judge whether the performance of the product meets the
requirements of relevant standards through verification, so as to
facilitate the design, improvement, verification and delivery
inspection of the product.
Ingress Protection Test
Standard:
IEC60529 degree of protection provided by enclosures (IP Code), clause 14.2.1, 14.2.2, 14.2.3, 14.2.4, 14.2.5, 14.2.6, 14.2.7, 14.2.8, and figure 3, figure 4, figure 5 and figure 6, IPX1, IPX2, IPX3, IPX4, IPX5 IPX6, IPX7 and IPX8, Table 3.
Application:
It is used to test the degrees of protection against ingress of water indicated by the second characteristic numeral. Ingress Protection Test Equipment
Second characteristic numeral | Degree of protection | Test conditions, see | |
| Brief description | Definition | ||
| 0 | Non-protected | - | - |
| 1 | Protected against vertically falling water drops | Vertically falling drops shall have no harmful effects | 1 4.2.1 |
| 2 | Protected against vertically falling water drops when enclosure tilted up to 1 5° | Vertically falling drops shall have no harmful effects when the enclosure is tilted at any angle up to 1 5° on either side of the vertical | 1 4.2.2 |
| 3 | Protected against spraying water | Water sprayed at an angle up to 60° on either side of the vertical shall have no harmful effects | 1 4.2.3 |
| 4 | Protected against splashing water | Water splashed against the enclosure from any direction shall have no harmful effects | 1 4.2.4 |
| 5 | Protected against water jets | Water projected in jets against the enclosure from any direction shall have no harmful effects | 1 4.2.5 |
| 6 | Protected against powerful water jets | Water projected in powerful jets against the enclosure from any direction shall have no harmful effects | 1 4.2.6 |
| 7 | Protected against the effects of temporary immersion in water | Ingress of water in quantities causing harmful effects shall not be possible when the enclosure is temporarily immersed in water under standardized conditions of pressure and time | 1 4.2.7 |
| 8 | Protected against the effects of continuous immersion in water | Ingress of water in quantities causing harmful effects shall not be possible when the enclosure is continuously immersed in water under conditions which shall be agreed between manufacturer and user but which are more severe than for numeral 7 | 1 4.2.8 |
| 9 | Protected against high pressure and temperature water jets | Water projected at high pressure and high temperature against the enclosure from any direction shall not have harmful effects | 1 4.2.9 |
Table 3 – Degrees of protection against water indicated by the second characteristic numeral
Parameter:
| 1. Protected against vertically falling water drops | |
| Application | Applies to conduct IPX1, IPX2 testing. |
| Rain area | 1000mmX600mm |
| Tank material | Stainless steel |
| Dripping aperture | Φ0.4mm |
| Hole distance | 20mm |
| Rainfall Flow | 1mm/Min, 3mm/Min, user-set parameters (error: + 0.5mm / min). |
| Water dripping height | 200mm (automatically control by the test equipment) |
| Test time | 10Min, can be set according to the need |
| Draining | Automatically emptying the tank water after the test is completed |
| Body material | Industrial aluminum alloy |
| Dimensions (LxDxH) | 1100X1200X2600mm |
| Machine structure | Wall Mount |
| Air compressor (Optional, not included) | Silent air compressor |
| 2. Protected against spraying and splashing water (oscillating tube) | |
| Application | Applies to conduct IPX3, IPX4 testing. |
| Water supply | Water flow rate＞10L/min±5% clean water without inclusion. This device is equipped with clean water filtration unit |
| The size of the oscillating tube | Standard coming with R400, R600, R800 oscillating tubes (other size R200,R1000,R1200,R1400,R1600mm can be optional), stainless steel |
| Water hole | Φ0.4mm. Ingress Protection Test Equipment |
| Included angle of two holes | IPX3: 120°; IPX4: 180° |
| pendulum angle | IPX3: 120°; IPX4: 360° |
| Raining speed | IPX3: 4s/time(2×120°); IPX4: 12s/time(2×360°); |
| Water flow | Can be set according to the size of the pendulum and the number of the pin holes (0.07 L/minX per hole) |
| Testing time | 0.01S～99 hours 59mins,can be preset |
| Pressure gauge | 0~0.25MPa |
| Site requirements | Dedicated IP waterproof test room, The ground should be flat with illumination 10A waterproof leakage switch(or socket)used for equipment. With good function of inflow and drainage. Ground installation |
| The area | According to the oscillating tube chose |
| 3. Protected against spraying and splashing water (Spray Nozzle) | |
| Water supply | Water flow rate is 50～150kpa clean water without inclusion. |
| Spray nozzle parameters | external diameter: Ф102mm spherical diameter: SФ75.5mm There is a middle hole and There are 24 holes in the internal circle of holes of which the included angle is 30°. There are 96 holes in the external circle of holes of which the included angle is 15°. 121 holes in total. The hole diameter: Ф0.5mm It is made of brass. |
| Water flow | 10L/min±5%, Flow meter is adjustable |
| Range of pressure gauge | 0～0.4Mpa |
| Baffle | removable |
| Pressure gauge | 0~0.25MPa |
| 4. Protected against water jets and powerful water jets | |
| Application | Applies to conduct IPX5, IPX6 testing. |
| Water supply | IPX5: Water flow rate ＞ 12.5L/min±5%; IPX6: Water flow rate ＞100L/min±5%; It can be achieved by the stainless steel water tank and pressurized equipment |
| The nozzle diameter | IPX5: Ф6.3mm; IPX6: Ф12.5mm |
| Water flow | IPX5: 12.5±0.625L/min, IPX6: 100±5 L/min; Flow meter is adjustable |
| The distance from jet nozzle to enclosure | 2.5~3m |
| Testing time | Not less than 1min/m²(not less than 3 mins) |
| Pressure gauge | 0~0.25MPa |
| 5. Protected against the effects of temporary immersion in water and electrical control cabinet | |
| Applicable | (a) Water supply for IPX1~IPX6 waterproof test (b) IPX7 water immersion test (c) Water storage for IPX8 water tightness test (d) Automatic control for the whole waterproof equipment |
| Water storage tank | It is applicable to water storage of IPX5~IPX6 strong water spray test, water injection of IPX8, IPX7 immersion Volume:500L Dimension: W600mmXD660mmXH1300mm Observation window: toughened glass window Observation window dimension: W200mmXH1250mm Depth gauge: stainless steel Depth gauge height: 1200mm, accuracy 1mm Liquid level control: float switch + overflow pipe |
| Control Cabinet | Flow detection: flow signal feedback through electronic flowmeter Flow setting: set on touch screen Controller: PLC Control Function: constant flow water supply, constant pressure water supply, and test time control. Protection function: leakage protection, overload protection, short circuit protection |
| IPX7 immersion automatic lift bracket | Lifting distance: 0~1200mm Bracket dimension: L400mmXW400mm Bracket load weight: 50Kg |
| 6. Protected against the effects of continuous immersion in water | |
| Application | Applies to conduct IPX8 testing. |
| Pressure vessel | Stainless steel tank, diameter 0.8 meter, height 1 meter |
| Pressure adjustment range | 0 ~ 6bar (can be customized) |
| Pressure system | Stainless steel pump + frequency converter |
| Pressure gauge accuracy | 0.25 degree, range: 10bar |
| Testing time | 0-99min |
| Maximum limit pressure | 6 bar |
| Pressure protection | Pressure switch protection |
| 7. Turntable | |
| Turntable diameter | Ø600mm |
| Sample holder | Ø600mm |
| Turntable speed | 1-5 rpm, adjustable |
| Tiltable angle | 15° |
| Test angle of rotation | 90° , continuous rotation |
| Adjustable height of the adjustable telescopic tube | 300mm, 1200mm-1500mm |
| Body material | Industrial aluminum alloy |
