Home Companies Guangzhou HongCe Equipment Co., Ltd.

2000x800x600mm JIS ASTM CNS Ingress Protection Test Equipment

Guangzhou HongCe Equipment Co., Ltd.

Contact Us

[China] country

Trade Verify

Address: Room 202, Building 4-2, No. 539, Shibei Industrial Road, Dashi Street, Panyu District, Guangzhou, Guangdong

Contact name:Tessa Huang

Inquir Now

Guangzhou HongCe Equipment Co., Ltd.

Verified Suppliers
  • Trust
    Seal
  • Verified
    Supplier
  • Credit
    Check
  • Capability
    Assessment

2000x800x600mm JIS ASTM CNS Ingress Protection Test Equipment

Country/Region china
City & Province guangzhou guangdong
InquireNow

Product Details

JIS / ASTM / CNS Ingress Protection Test Equipment Salt Spray Chamber 2000x800x600mm

 

 

Product Introduction:

The salt spray test machine is used for the surface treatment of various materials, including coatings, electroplating, organic and inorganic coatings, anodizing, anti-rust oil and other anti-corrosion treatments to test its corrosion resistance, thus establishing the quality of the product.

 

Inner chamber introduction:

 

Spray towerThe built-in glass nozzle is placed inside the spray tube, and the spray is guided through the tower tube and dispersed into the test chamber through the cone disperser.
Spray regulatorAdjust the quantity of spray by increasing or decreasing it. The preheating tank of salt water is at the bottom of the spray tower. Its salt water is injected into to tank from refill bottle. The water level is controlled by float ball automatically. Drain outlet for cleaning is stuck by silicone cork at the bottom of the tank.
CollectorThe spray from the spray nozzles will fall into a 80cm2 V-shape container in free fall way and will be led to measure cup by tube.
RackThe rack is made of plastic-steel. The maximum rack load shall be 2kg for single lading point or 10kg for scattered lading points.
Heating tankThe U-shaped heating tube is equipped with a heating tank for the test chamber, which is used for heating water to keep the temperature in the test chamber stable, and its function is heating and heat preservation.
Metering tubeCollect the spray volume for each test.
Water-sealed tank:A 5cm wide water tank around the transparent acrylic cover is sealed with water to prevent salt spray from leaking.
Saturated air pailIt is placed inside the control box, and its function is to heat and humidify the air through this pail, so that the air reaches the saturated humidity and sprays.
Test inletAutomatically replenish the salt solution of the brine preheating tank.
Chamber coverA roof-like transparent top with 100º angle which cover the machine testing body and unify it.
Adjust press valveThis valve is used to adjust the spray pressure. It can only be adjusted when the spray switch is turned on and the machine is operating normally (test conditions 1Kg / cm²)
Pressure meter

It shows the pressure of the air from the saturated-air pail to the

nozzle (testing pressure: 1kg/cm2)

Exhaust pipeThe diameter of the exhaust pipe is 48mm. The spray in the chamber is discharged through this hole. When testing, it is best to connect a hose to lead the spray to the outside. Do not block or have water accumulation.
Chamber drain valveThe red ball valve is equipped with a 4-point PVC water pipe. This valve is opened when the chamber water is dirty and the chamber water needs to be replaced.
Test chamber temperature controllerControl the temperature in the chamber according to standards, the temperature of the chamber is controlled at 35 ℃.
Saturated-air pail temperature controllerControl the temperature in the saturated-air pail, another safety protection device, the temperature safety set value is 5 ° C higher than the actual temperature. (Located in the control box)
TimerSet testing time from 0.1s to 9999hr and stop the machine when the time expires.
Salt water spray test35℃ for test chamber controller and 47℃(40℃-50℃)for saturated-air pail controller.
Corrosion-resistant test50℃ for test chamber controller and 65℃(60℃-70℃)for saturated-air pail controller.
Power switchIlluminated rocker switch. Control the mains of the whole machine.
Operation switchIlluminated rocker switch. Control the water-heater tank and the heater system of saturated-air pail.
Timer switchIlluminated rocker switch. Control the power of timer.
Spray switchIlluminated rocker switch. Control the spray system.
Defogger switchIlluminated rocker switch type. Control the defogger system and get rid of the salt spray inside the box.
Chamber water shortage lampThe light will be turned on and the operation will be stopped when the water level in the chamber is lower than the limit.
Pressure water shortage lampThe light will be turned on and the operation will be stopped when the water level in the saturated-air pail is lower than the limit.
Lack brine lampThe light will be turned on and the operation will be stopped when the water level of preheating tank of salt water is lower than the limit.
 

 

Product front view A:                                                                       Product back view B:

 

A:B:
1.Test chamber8.Compressed air inlet
2. Manual water filling place for pressure pail9.Exhaust
3.Metering tube10.Power supply 230V
4.Brine inlet11.Chamber drainage valve
5.Control plane12.Cover support frame
6. Adjust press valve 
7.Control box door 
 


Technical Parameters:

 

ModelHH0813D
Inner chamber size (mm)2000x800x600mm(W*D*H)
Outer chamber size (mm)2300x1100x1400mm(W*D*H)
Test chamber temperatureSalt water test method (NSS ACSS AASS)35℃±1℃/ corrosion resistance test method(CASS)50℃±1℃
Pressure barrel temperatureSalt water test method(NSS ACSS AASS)47℃±1℃/ corrosion resistance test method(CASS)63℃±1℃
Salt concentrationThe concentration of sodium chloride 5% or the 5% concentration of sodium chloride add 0.26g per liter of copper chloride (CuCl2 2H2O)
Compressed air pressure1.00±0.01kgf/cm²
Spray amount1.0~2.0ml/80cm²/h (collecting at least for 16 hours, take the average)
Relative humidity of testing chamberMore than 85%
Acid value PH6.5~7.2 3.0~3.2
Spray modeProgrammable spray (including continuous spray and intermittent spray)
Meet the standardsJIS, ASTM, CNS
Power supply230V, 60Hz
 

Picture View:

Hot Products

IEC60730-1 IEC Test Equipment Label Marking Abrasion Test Machine Sliding Weight 500g Production ...
IEC 60898 Test Equipment Test Of Time-Current Characteristic With 8 Stations Standard: IEC 60898-1 ...
Spring Operated Impact Hammer for IEC60068-2-75 IEC Test Equipment Standard: IEC 60068-2-75 ...
IEC60990 Figure 4 Touch Current Measuring Network, Convenient to Use​ Products Introduction: This ...
IEC60990 Figure 5 Touch Current Measuring Network, Convenient to Use​ Applicable object: 1. ...
IEC 60745-2-5 Circular Saw Lower Guard Test Device, 0-30 times / min Standard: IEC 60745-2-5 : ...