|
[China]
Trade Verify
Address: A507 5F, China Zhenhua Production Center, 64Heping Road, Longhua,Shenzhen,China
Contact name:Sophie
YINGDA TECHNOLOGY LIMITED |
|
Verified Suppliers
|
|
|
SC Quick Connector Optical Fiber Drop Cable Termination 55mm No Need Epoxy SM TPU Repeat Use
Fast field-installable connectors are factory pre-polished connectors that completely eliminate the need for hand polishing in the field. Proven mechanical splice technology ensuring precision fiber alignment, a factory pre-cleaved fiber stub and a proprietary index-matching gel combine to offer an immediate low loss termination to either single-mode or multimode optical fibers.
Fast connectors are compatible with 250µm and 900µm optical fibers, as well as 900µm, 2mm and 3mm cordage. All primary fiber types are supported, and each connector is color coded per industry-standard requirements to aide in identification during and after installation. A factory-installed wedge clip (included with each connector) is removed and discarded upon completion of the termination.
Features
No epoxy required
Fiber can be reseated
Pre-stubbed, factory-polished ferrule
Precision mechanical alignment insures low loss
VFI can be used to confirm fiber is installed properly
Meets TIA/EIA 568A performance requirements
Meets TIA/EIA 604 (focis) connector interface requirements
Applications
Premise environments
Connections at the desk for LAN environments
Direct equipment termination
Fiber to the Subscriber (FTTx) applications
Repair and replacement requirements
Equipment test leads
Patch panels
singlemode APC or PC both can do. Fiber moe: APC green house,PC blue house.
gray part is clip for repeat use, it can be take off by hand, round boot is screw on and off
3mm round or 2x3mm figure-8 drop cable can insert from boot, high quality ceramic ferrule and pre-polished fiber inside.
Specification
| Item | Parameter |
| Single-Mode | |
| Insertion Loss | Max≤0.5dB , Average≤0.3dB |
| Return Loss | APC≥50dB;UPC≥45dB |
| Durability (1000 Mating) | 0.2dB Max. |
| Operating Temperature | -40°C~+75°C |
Mechanical performance requirements
| Test name | Test condition | Result | ||
| Insertion loss change | Return loss change | Outer appearance change | ||
| Repeat assembly | Repeat: 5imes | ≤0.3dB | ＜0.5dB | Can be reassembled and test, pin surface should be no obvious scratches, if insertion loss change is large than 0.3dB, qualified; the rest shall not have mechanical damage, deformation, crack, relaxation and other anomalies |
| Tensile strength | 0.125mm bare fiber 4N, 0.25mm fiber 4N,non-online monitoring optical performance; 0.9mm optical fiber type 10N, optical cable 20N, on-line monitoring optical performance; cable 30N, not online monitoring optical performance; Time: 2 minutes | ≤0.3dB | ＜0.5dB | |
| Drop test | Height: distance from the sample head 1.5m; times: 10 times | ≤0.3dB | ＜0.5dB | |
| Vibration | Frequency: 10 ~ 50Hz; sweep: 45 times per minute: amplitude: 0.75mm single amplitude; time: three directions, each two hours | ≤0.3dB | ＜0.5dB | |
| Repeatability | Mating:10times | ≤0.3dB | ＜0.5dB | |
| Mechanical durability | Mating:500times | ≤0.3dB | ＜0.5dB | |
| Retortion | Load: cable type 15N; rate: 10 times / min; times: 200 times | ≤0.3dB | ＜0.5dB | |
