Active Member
|
[China]
Address: 5 Floor,SongShan Building B14, YinTian Industrial Zone, Baoan District, Shenzhen,China
Contact name:James Shaw
Shenzhen Flier Electronic Co., Ltd. |
|
|
Basic information
Voltage | Working Current | Size(mm) | weight(g) | BEC (Volts/Amps) | Box Programming support | Computer Programming support | Capacitor | |
67V | 100A | 115*52*20 | 350g | OPTO | Yes | Yes | 80V |
Feature:
1. Design for RC Boat, more functions
2. Battery voltage from 12V to 67V for super high voltage version.
3. Two way communication while connecting it with computer.
4. Firmware can be upgrade by user.
5. Motor cable can be inspected while Connecting the power battery
6. Simply set function value by Prog-Box or by PC via USB link
wire.
7. Li-MH/Li-Po,Ne-Cd/Ne-mH,LiFe battery can be use.
8. Enables setting the voltage per cell for the point at which the
controller’s cut off circuitry engages.Li-MH/Li-Po from
2.0-3.6V,Ne-Cd/Ne-mH 0.4-1.0V,LiFe from2.2-2.8V
9. Reverse function. the delay time of reverse is adjustable
10. The power of the motor forward/ reverse can be set.
11. Automatically detection the throttle route or can be set a
fixed number by manual operation.
12. Auto cut off the power within 3 seconds if no radio signs.
13. Timing setting may be adjusted (0°-30°) to suit the motor type.
How the ESC to control the motor speed?
Set the required speed with the speed adjustment potentiometer. The sensor measures the actual value of the engine speed through the ring gear on the flywheel and sends it to the controller. The actual value in the controller is compared with the set value. The control line is arranged and enlarged, and the output shaft of the actuator is driven. The fuel pump pin is pulled by adjusting the connecting rod to adjust the oil supply amount, thereby achieving the purpose of maintaining the set rotation speed.
This electronic governor can also choose the size of the unevenness according to the needs of the engine. When the stepless speed regulation is performed, the electronic control system eliminates the difference between the set speed and the actual speed caused by the load change, so that the engine maintains the original set speed. According to the needs of the unit, the unevenness potentiometer can also be adjusted to achieve a satisfactory static adjustment rate of the speed control system.
The electronic governor is also equipped with a variety of accessory devices. According to the needs of the unit, the corresponding accessories can be installed to realize the functions of automatic synchronization, load distribution and load preset.
The electronic governor is characterized by the ability to independently determine the speed regulation characteristics, and to determine the optimum torque characteristics, idle speed characteristics and transition characteristics when all accessories are installed. The electronic dispatcher can adapt to the requirements of different models.
Software:
1. Reverse: On/Off.
2. Timing:0°,1°,2°,3°,4°……30°.
3. Frequency: 8KHz, 16 KHz, 32 KHz.
4. Acceleration: Soft / Medium / Hard.
5. Accumulator type:NiCd/NiMh,Li-Ion/Li-Pol,LiFe.
6. NiCd/NiMH CUTOFF:×0.05,0.4V,0.5V,0.6V,0.7V,0.8V,0.9V,1.0V.×0.05 means the cut off voltage
is 5% the voltage while connecting.
7. Number of cells:Auto,2S,3S,4S,5S,6S,7S,8S,9S,10S,11S,12S,16S.
8. LiIo/Pol
CUTOFF:2.0V,2.1V,2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V,2.9V,3.0V,3.1V,3.2V,3.3V,3.4V,3.5V,3.6V.
9. LiFe cutoff:2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V
10. Cut Off Type::Slow down,Hard. l
11. Power limited forward: Off, 75%, 50%, 25%.
12. Power limited reverse: Off, 75%, 50%, 25%.
13. Delay time when direction convert: 0.25S, 0.5S, 0.75S, 1S,
1.5S, 2S, 3S, 5S.
14. Reverse point:Auto,fixed 1.0mS,fixed 1.1mS,fixed 1.2mS,fixed 1.3mS.
15. Forward point:Auto,fixed 1.7mS,fixed 1.8mS,fixed 1.9mS,fixed 2.0mS.
16. Throttle curve: Logarithmical,Linear,Exponential.
17. Rotation direction: Left, Right.
18. Timing monitor (TIMING MONTITOR): ON, Off.
Note:the red mark is the factory default value,you can setting
function value by youself.
Trade Terms:
1. Payment :T/T ,Paypal,West union .
2. Production lead time :5 days for 100-200 pcs ,10days for
200-300pcs .
3. Sample can be delivered within 3 days.
4. Discounts are offered based on order quantities .
5. MOQ: 2 pcs.
Shipping&Return:
1. Items will be shipped within 3 business day after payment
completed received.
2. Items are shipped from DHL Express ,UPS ,EMS,, reach most of the
countries within 3-7 days respectively.
3. Warranty Period is 2 yrs for this item.
4. If product can not work, or find it as defects within in 7 days
after receipt, please contact us, we will replace or refund.
5. All emails will be answered within 1 working day.
