Active Member
|
[China]
Address: 5 Floor,SongShan Building B14, YinTian Industrial Zone, Baoan District, Shenzhen,China
Contact name:James Shaw
Shenzhen Flier Electronic Co., Ltd. |
|
|
16S 200A rc intelligent brushless controller for rc esc Skate
Basic information:
| Voltage | Current | Size(mm) | weight(g) | BEC (Volts/Amps) | Box Programming support | Computer Programming support | Firmware update | |
| 4-16S | 200A | 125*57*22 | 256g | OPTO | Yes | Yes | Yes |
ESC Info:
Design for skateboard, more functions.
1:There are three pins wires for the receiver port, length is
300mm:
---The brown wire is ground,
---The yellow wire is pulse signal wire, it is a 5V PWM pulse
signal and you just controll the ESC via the wire,
---The red wire is the power wire 5V input to the ESC; you must
supply a 5V voltage to the red wire otherwise the ESC won't work.
2:A standard receiver signal is 1-2mS@50Hz. It is saild that the receiver will send 1-2mS 5V pulse per 20mS to the ESC. 1mS pulse will arm the ESC,and the motor will stop. when increase the throttle, the pulse width also increase, about 1.1mS, the motor will start to spin, and 2mS, the motor will spin at full speed.
3:Baterry wire: length 180mm, 8AWG. Red wire connect to the positive pole, black connect to the negative pole. The black side of the small black 18AWG line is Anti-spark wire,It is built in a bullet connector and a 10 ohms resistor. You must connect the end of the wire to the battery negative. you can connect the red wire of ESC to the positive pole of battery at first. Then connect the anti-spark wires well. The last step is to connect the black wire of ESC to the battery’s negative pole. If do so, no spark will be generated, and this will protect the main bullets connector from spark damage.
4.Motor wire; 3 pcs balck wire, 8AWG, 180mm.
5.Program wire: 4 pins, length 100mm. Use USB link to program via PC or program via program box.
Feature:
1.Battery voltage 1S=4.2V
2.The ESC firmware can be updated by the user.
3.It can be connected to the programming box or connected to the computer through the USB cable, which is very convenient to set various parameters of the brushless ESC.
4.Single cell protection shutdown voltage, adjustable from 0.1V.
5.The motor advance angle is from 0 to 30 degrees and can be adjusted step by step.
6.The three types of throttle response curves can be set to different acceleration sensations.
7.With reverse function, and reverse delay time is adjustable.
8.With forward/reverse power limit function
9.Li-MH/Li-Pofrom 2.0-3.6V, Ne-Cd/Ne-0.4-1.0V, LiFefrom 2.2-2.8V.
10.It has automatic throttle detection and manual setting of a fixed value function.
11.Over temperature protection 110 ° C.
12.The remote control signal is automatically turned off after 3 seconds of loss.
Setting function value:
1. Reverse: On/Off.
2. Timing:0°,1°,2°,3°,4°……30°.
3. Frequency: 8KHz, 16 KHz, 32 KHz.
4. Acceleration: Soft / Medium / Hard.
5. Accumulator type:NiCd/NiMh,Li-Ion/Li-Pol,LiFe.
6. NiCd/NiMH CUTOFF:×0.05,0.4V,0.5V,0.6V,0.7V,0.8V,0.9V,1.0V.×0.05 means the cut off voltage is 5% the voltage while connecting.
7. Number of cells:Auto,2S,3S,4S,5S,6S,7S,8S,9S,10S,11S,12S,16S.
8. LiIo/Pol CUTOFF:2.0V,2.1V,2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V,2.9V,3.0V,3.1V,3.2V,3.3V,3.4V,3.5V,3.6V.
9. LiFe cutoff:2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V
10. Cut Off Type::Slow down,Hard. l
11. Power limited forward: Off, 75%, 50%, 25%.
12. Power limited reverse: Off, 75%, 50%, 25%.
13. Delay time when direction convert: 0.25S, 0.5S, 0.75S, 1S, 1.5S, 2S, 3S, 5S.
14. Reverse point:Auto,fixed 1.0mS,fixed 1.1mS,fixed 1.2mS,fixed 1.3mS.
15. Forward point:Auto,fixed 1.7mS,fixed 1.8mS,fixed 1.9mS,fixed 2.0mS.
16. Throttle curve: Logarithmical,Linear,Exponential.
17. Rotation direction: Left, Right.
18. Timing monitor (TIMING MONTITOR): ON, Off.
Note:the red mark is the factory default value,you can setting function value by youself.
Pictures:
Trade Terms:
1.Payment :T/T ,Paypal,West union .
2.Production lead time :5 days for 100-200 pcs ,10days for 200-300pcs .
3.Sample can be delivered within 3 days.
4.Discounts are offered based on order quantities .
5.MOQ: 2 pcs.
Shipping&Return:
1. Items will be shipped within 3 business day after payment completed received.
2. Items are shipped from DHL Express ,UPS ,EMS,, reach most of the countries within 3-7 days respectively.
3. Warranty Period is 2 yrs for this item.
4. If product can not work, or find it as defects within in 7 days after receipt, please contact us, we will replace or refund.
5. All emails will be answered within 1 working day.
