|
[China]
Trade Verify
Address: No. 317, Yichun South Road ( Happiness Park), Yuanzhou District, Yichun, Jiangxi, 336000, China
Contact name:Penny Peng
Pego Electronics (Yi Chun) Company Limited |
|
Verified Suppliers
|
|
|
IEC60950 Test Probe Kit Contains Jointed Finger Probe Rigid Test Finger Ball Pressure Test Apparatus ect.
The PG-60950 contains the devices listed in the core of the UL / IEC / EN 60950 requirements. It includes the following probes:
1. Jointed Finger Probe
| Diameter of finger: | 12mm | Length of finger: | 80mm |
| Diameter of baffle: | 50mm | Length of baffle: | 100mm |
| Thruster (optional) | 10N | ||
| Material: Insulating material (baffle and handle), stainless steel(finger) | |||
2. 50mm Impact Test Ball
2.1 Impact steel ball: Φ50mm, 500±25g
3. Short Test Pin Probe
3.1 Introduction:
The Short Test Pin Probe (conical short taper test pin : Φ3~4-length 15) is designed according to IEC61032 figure 9. The pin is intended to verify the protection against access to hazardous live parts in class 0 equipment and class II equipment (see IEC60536)
3. 2.Specification:
| diameter of test pin | head 3mm, bottom 4mm |
| length of test pin | 15mm |
| diameter of baffle | 25mm |
| thickness of baffle | 4mm |
| material | insulating material, metal |
4. Rigid Finger Probe
4.1 Introduction:
Rigid Finger Probe (unjointed test finger) is designed according to IEC61032 figure 7 and UL clauses. This probe may be used to verify the protection of persons against access to hazardous parts, and to verify the mechanical strength of openings in the enclosure or internal barriers. 50N force recommend to be applied.
4.2 Specification:
| diameter of test finger | 12mm |
| Length of test finger | 80mm |
| Diameter of baffle | 50mm |
| Thickness of baffle: | 5mm |
| Strength range | 10N, 20N, 30N, 40N, 50N |
| Material | insulating material, metal |
5. Ball Pressure Tester
The ball pressure tester is designed according to IEC60695-10-2, IEC60335, IEC60601, GB4706.1 and etc. the surface of the part to be tested is placed in the horizontal position and a steel ball of 5 mm diameter is pressed against the surface with a force of 20 N. The test is performed in a heating cabinet at a temperature of 75°C ± 2°C. The ball is withdrawn after 1 h and the diameter of the impression made by the ball is measured. An impression greater than 2 mm in diameter constitutes a failure.
5.1 Parameters
| Ball diameter | 5mm (R2.5mm) |
| Test Pressure | 20N±0.2N |
| Material | Stainless Steel |
| Sample supportor | Φ50mm-length 100mm, cylinder sharp |
6. Telecom Test Probe
This telecom test probe is designed according to the standard of IEC60950, IEC60065, IEC60695.
6.1 Application
It is used to check for limited access to telecommunications voltages (TNV), mainly telephone jacks and operator areas. Satisfied basic standard for telecom product safety.
6.2 Technical parameter
| Test probe diameter | 12mm |
| Test probe length | 80mm |
| Dam-board diameter | 50mm |
| Material | nylon and stainless steel |
| Reference | IEC60950, IEC60065,IEC60695 |
The IEC60950 Test Probe are packed in a custom-cut foam padded silver case and can be required with the ISO17025 accredited certificates of calibration -- with specific scope for “Accessibility Probes”. And it meets requirements for testing standards including but not limited to UL/EN/UIEC/CAS 60950.
